RAID attributes uses scsi_is_sdev_device() to gate some SCSI specific
checking code.  This causes two problems.  Firstly if SCSI == n just
defining scsi_is_sdev_device() to return false might not be enough to
prevent gcc from emitting the code (and thus referring to undefined
symbols), so this needs surrounding with an ifdef.  Secondly, using
scsi_is_sdev_device() when SCSI is either y or m gives a subtle
problem in the m case: raid_attrs must also be m to use the symbol.
Do the usual Kconfig jiggery-pokery to fix this.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

This driver supports a subset of HP Smart Array Controllers.
It is a SCSI alternative to the cciss driver.

[akpm@linux-foundation.org: avoid helpful cleanup patches]
[achiang@hp.com: make device attrs static]
[akpm@linux-foundation.org: msleep() does set_current_state() itself]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Use libfcoe as a common FIP implementation with fcoe.
FIP or non-FIP mode is fully automatic if the firmware
supports and enables it.

Even if FIP is not supported, this uses libfcoe for the non-FIP
handling of FLOGI and its response.

Use the new lport_set_port_id() notification to capture
successful FLOGI responses and port_id resets.

While transitioning between Ethernet and FC mode, all rx and
tx FC frames are queued.  In Ethernet mode, all frames are
passed to the exchange manager to capture FLOGI responses.

Change to set data_src_addr to the ctl_src_addr whenever it
would have previously been zero because we're not logged in.
This seems safer so we'll never send a frame with a 0 source MAC.
This also eliminates a special case for sending FLOGI frames.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[jejb: fix up for new queue depth code]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

This is a driver for VMware's paravirtualized SCSI device,
which should improve disk performance for guests running
under control of VMware hypervisors that support such devices.

Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.

Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[v2: fixed up virt_to_bus() issue spotted by sfr]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Add new driver for Brocade Hardware

Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

People keep sending patches to expose CONFIG_SCSI_WAIT_SCAN as a tunable
item.  These patches aren't accepted upstream, so let's stop the ongoing
irritation of people due to the unconditionally installed module and its
Kconfig symbol.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>