CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Modified the firmware naming convention to contain the
  firmware image version (3.1.0.0).
- The new convention is <firmware-image>-<firmware-version>.bin
- The change will enforce loading only compatible firmware with this driver
  and also avoid over-writing the old firmware image in-order to load new
  version driver as the firmware names used to be the same.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Add FRU sub-module to support FRU read/write/update.
- Add support to read/write from the temp FRU module.

[jejb: fix checkpatch issues]
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Add Power On Hours display support during sfpshow
- Fix to properly set the diag temperature sensor status variable.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Added support to configure minimum bandwidth for a pcifn.
- Minimum bandwith is guaranteed at per queue level.
- Added support to update pcifn bandwidth dynamically without
  a server reboot.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Add capability to limit the number of exchanges on a port to
avoid queue-full conditions from the target side.

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Made changes to provide an option for user to configure the
bandwidth percentage for High/Medium/Low QoS priorities.

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Made changes such that once the PWWN is acquired from the fabric through FAA,
  and if the FAPWWN configuration is modified on the switch side, driver should
  show relevant information to the user.
- Added logic to cache the reason code when the given port is disabled implicitl
  due to FAA error condition.
- If the port is disabled, while sending SCN to upper layer, update the
  reason code appropriately. With this, BFA FC port state machine will enter
  into faa_err_config state. This state will be shown to the user.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Introduced support for D-Port which is a new port mode during which
  link level diagnostics can be run.
- Provided mechanism to dynamically configure D-Port and initiate diagnostic
  tests to isolate any link level issues.
- In D-Port mode, the HBA port does not participate in fabric or login to the
  remote device or run data traffic.
- Diagnostic tests include running various loopback tests in conjunction with
  the attached device.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>