linux-toradex.git/drivers/scsi/mvsas, branch v3.2.42 Linux kernel for Apalis and Colibri modules mvsas: Fix oops when ata commond timeout. 2013-01-16T01:13:27+00:00 Jianpeng Ma majianpeng@gmail.com 2012-08-04T02:34:14+00:00 3b6ee0c4b85c6697d88593e164f79d79c398aa0b commit 95ab000388974d8ffef8257306b4be6e8778b768 upstream. Kernel message follows: [ 511.712011] sd 11:0:0:0: [sdf] command ffff8800a4e81400 timed out [ 511.712022] sas: Enter sas_scsi_recover_host busy: 1 failed: 1 [ 511.712024] sas: trying to find task 0xffff8800a4d24c80 [ 511.712026] sas: sas_scsi_find_task: aborting task 0xffff8800a4d24c80 [ 511.712029] drivers/scsi/mvsas/mv_sas.c 1631:mvs_abort_task() mvi=ffff8800b5300000 task=ffff8800a4d24c80 slot=ffff8800b5325038 slot_idx=x0 [ 511.712035] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 [ 511.712040] IP: [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30 [ 511.712047] PGD 0 [ 511.712049] Oops: 0002 [#1] SMP [ 511.712052] Modules linked in: mvsas libsas scsi_transport_sas raid456 async_pq async_xor xor async_memcpy async_raid6_recov raid6_pq async_tx [last unloaded: mvsas] [ 511.712062] CPU 3 [ 511.712066] Pid: 7322, comm: scsi_eh_11 Not tainted 3.5.0+ #106 To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M. [ 511.712068] RIP: 0010:[<ffffffff815f8c0c>] [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30 [ 511.712073] RSP: 0018:ffff880098d3bcb0 EFLAGS: 00010086 [ 511.712074] RAX: 0000000000000286 RBX: 0000000000000058 RCX: 00000000000000c3 [ 511.712076] RDX: 0000000000000100 RSI: 0000000000000046 RDI: 0000000000000058 [ 511.712078] RBP: ffff880098d3bcb0 R08: 000000000000000a R09: 0000000000000000 [ 511.712080] R10: 00000000000004e8 R11: 00000000000004e7 R12: ffff8800a4d24c80 [ 511.712082] R13: 0000000000000050 R14: ffff8800b5325038 R15: ffff8800a4eafe00 [ 511.712084] FS: 0000000000000000(0000) GS:ffff8800bdb80000(0000) knlGS:0000000000000000 [ 511.712086] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 511.712088] CR2: 0000000000000058 CR3: 00000000a4ce6000 CR4: 00000000000407e0 [ 511.712090] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 511.712091] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 511.712093] Process scsi_eh_11 (pid: 7322, threadinfo ffff880098d3a000, task ffff8800a61dde40) [ 511.712095] Stack: [ 511.712096] ffff880098d3bce0 ffffffff81060683 ffff880000000000 0000000000000000 [ 511.712099] ffff8800a4d24c80 ffff8800b5300000 ffff880098d3bcf0 ffffffffa0076a88 [ 511.712102] ffff880098d3bd50 ffffffffa0079bb5 ffff880000000000 ffff880000000018 [ 511.712106] Call Trace: [ 511.712110] [<ffffffff81060683>] complete+0x23/0x60 [ 511.712115] [<ffffffffa0076a88>] mvs_tmf_timedout+0x18/0x20 [mvsas] [ 511.712119] [<ffffffffa0079bb5>] mvs_slot_complete+0x765/0x7d0 [mvsas] [ 511.712125] [<ffffffffa005a17d>] sas_scsi_recover_host+0x55d/0xdb0 [libsas] [ 511.712128] [<ffffffff8106d600>] ? idle_balance+0xe0/0x130 [ 511.712133] [<ffffffff813b150c>] scsi_error_handler+0xcc/0x470 [ 511.712136] [<ffffffff815f7ad0>] ? __schedule+0x370/0x730 [ 511.712139] [<ffffffff8105f728>] ? __wake_up_common+0x58/0x90 [ 511.712142] [<ffffffff813b1440>] ? scsi_eh_get_sense+0x110/0x110 [ 511.712146] [<ffffffff810571be>] kthread+0x8e/0xa0 [ 511.712150] [<ffffffff816015f4>] kernel_thread_helper+0x4/0x10 [ 511.712153] [<ffffffff81057130>] ? flush_kthread_work+0x120/0x120 [ 511.712156] [<ffffffff816015f0>] ? gs_change+0xb/0xb [ 511.712157] Code: 8a 00 01 00 00 89 d0 f0 66 0f b1 0f 66 39 d0 0f 94 c0 0f b6 c0 5d c3 0f 1f 84 00 00 00 00 00 55 48 89 e5 9c 58 fa ba 00 01 00 00 <f0> 66 0f c1 17 0f b6 ce 38 d1 74 11 0f 1f 84 00 00 00 00 00 f3 [ 511.712191] RIP [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30 [ 511.712194] RSP <ffff880098d3bcb0> [ 511.712196] CR2: 0000000000000058 [ 511.712198] ---[ end trace a781c7b1e65db92c ]--- Signed-off-by: Jianpeng Ma <majianpeng@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 95ab000388974d8ffef8257306b4be6e8778b768 upstream.

Kernel message follows:

[  511.712011] sd 11:0:0:0: [sdf] command ffff8800a4e81400 timed out
[  511.712022] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[  511.712024] sas: trying to find task 0xffff8800a4d24c80
[  511.712026] sas: sas_scsi_find_task: aborting task 0xffff8800a4d24c80
[  511.712029] drivers/scsi/mvsas/mv_sas.c 1631:mvs_abort_task()
mvi=ffff8800b5300000 task=ffff8800a4d24c80 slot=ffff8800b5325038
slot_idx=x0
[  511.712035] BUG: unable to handle kernel NULL pointer dereference at
0000000000000058
[  511.712040] IP: [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30
[  511.712047] PGD 0
[  511.712049] Oops: 0002 [#1] SMP
[  511.712052] Modules linked in: mvsas libsas scsi_transport_sas
raid456 async_pq async_xor xor async_memcpy async_raid6_recov raid6_pq
async_tx [last unloaded: mvsas]
[  511.712062] CPU 3
[  511.712066] Pid: 7322, comm: scsi_eh_11 Not tainted 3.5.0+ #106 To Be
Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M.
[  511.712068] RIP: 0010:[<ffffffff815f8c0c>]  [<ffffffff815f8c0c>]
_raw_spin_lock_irqsave+0xc/0x30
[  511.712073] RSP: 0018:ffff880098d3bcb0  EFLAGS: 00010086
[  511.712074] RAX: 0000000000000286 RBX: 0000000000000058 RCX:
00000000000000c3
[  511.712076] RDX: 0000000000000100 RSI: 0000000000000046 RDI:
0000000000000058
[  511.712078] RBP: ffff880098d3bcb0 R08: 000000000000000a R09:
0000000000000000
[  511.712080] R10: 00000000000004e8 R11: 00000000000004e7 R12:
ffff8800a4d24c80
[  511.712082] R13: 0000000000000050 R14: ffff8800b5325038 R15:
ffff8800a4eafe00
[  511.712084] FS:  0000000000000000(0000) GS:ffff8800bdb80000(0000)
knlGS:0000000000000000
[  511.712086] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  511.712088] CR2: 0000000000000058 CR3: 00000000a4ce6000 CR4:
00000000000407e0
[  511.712090] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  511.712091] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7:
0000000000000400
[  511.712093] Process scsi_eh_11 (pid: 7322, threadinfo
ffff880098d3a000, task ffff8800a61dde40)
[  511.712095] Stack:
[  511.712096]  ffff880098d3bce0 ffffffff81060683 ffff880000000000
0000000000000000
[  511.712099]  ffff8800a4d24c80 ffff8800b5300000 ffff880098d3bcf0
ffffffffa0076a88
[  511.712102]  ffff880098d3bd50 ffffffffa0079bb5 ffff880000000000
ffff880000000018
[  511.712106] Call Trace:
[  511.712110]  [<ffffffff81060683>] complete+0x23/0x60
[  511.712115]  [<ffffffffa0076a88>] mvs_tmf_timedout+0x18/0x20 [mvsas]
[  511.712119]  [<ffffffffa0079bb5>] mvs_slot_complete+0x765/0x7d0
[mvsas]
[  511.712125]  [<ffffffffa005a17d>] sas_scsi_recover_host+0x55d/0xdb0
[libsas]
[  511.712128]  [<ffffffff8106d600>] ? idle_balance+0xe0/0x130
[  511.712133]  [<ffffffff813b150c>] scsi_error_handler+0xcc/0x470
[  511.712136]  [<ffffffff815f7ad0>] ? __schedule+0x370/0x730
[  511.712139]  [<ffffffff8105f728>] ? __wake_up_common+0x58/0x90
[  511.712142]  [<ffffffff813b1440>] ? scsi_eh_get_sense+0x110/0x110
[  511.712146]  [<ffffffff810571be>] kthread+0x8e/0xa0
[  511.712150]  [<ffffffff816015f4>] kernel_thread_helper+0x4/0x10
[  511.712153]  [<ffffffff81057130>] ? flush_kthread_work+0x120/0x120
[  511.712156]  [<ffffffff816015f0>] ? gs_change+0xb/0xb
[  511.712157] Code: 8a 00 01 00 00 89 d0 f0 66 0f b1 0f 66 39 d0 0f 94
c0 0f b6 c0 5d c3 0f 1f 84 00 00 00 00 00 55 48 89 e5 9c 58 fa ba 00 01
00 00 <f0> 66 0f c1 17 0f b6 ce 38 d1 74 11 0f 1f 84 00 00 00 00 00 f3
[  511.712191] RIP  [<ffffffff815f8c0c>] _raw_spin_lock_irqsave+0xc/0x30
[  511.712194]  RSP <ffff880098d3bcb0>
[  511.712196] CR2: 0000000000000058
[  511.712198] ---[ end trace a781c7b1e65db92c ]---

Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mvsas: fix undefined bit shift 2013-01-03T03:33:21+00:00 Xi Wang xi.wang@gmail.com 2012-11-16T19:40:03+00:00 463c45b0cdd91bf8426330373e5d292b002c5617 commit beecadea1b8d67f591b13f7099559f32f3fd601d upstream. The macro bit(n) is defined as ((u32)1 << n), and thus it doesn't work with n >= 32, such as in mvs_94xx_assign_reg_set(): if (i >= 32) { mvi->sata_reg_set |= bit(i); ... } The shift ((u32)1 << n) with n >= 32 also leads to undefined behavior. The result varies depending on the architecture. This patch changes bit(n) to do a 64-bit shift. It also simplifies mv_ffc64() using __ffs64(), since invoking ffz() with ~0 is undefined. Signed-off-by: Xi Wang <xi.wang@gmail.com> Acked-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit beecadea1b8d67f591b13f7099559f32f3fd601d upstream.

The macro bit(n) is defined as ((u32)1 << n), and thus it doesn't work
with n >= 32, such as in mvs_94xx_assign_reg_set():

	if (i >= 32) {
		mvi->sata_reg_set |= bit(i);
		...
	}

The shift ((u32)1 << n) with n >= 32 also leads to undefined behavior.
The result varies depending on the architecture.

This patch changes bit(n) to do a 64-bit shift.  It also simplifies
mv_ffc64() using __ffs64(), since invoking ffz() with ~0 is undefined.

Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[SCSI] mv_sas: OCZ RevoDrive3 & zDrive R4 support 2011-10-31T09:29:01+00:00 Robin H. Johnson robbat2@gentoo.org 2011-10-24T22:30:08+00:00 99a700bcc75429ba84a672d04f0b650dcc5b3042 In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage Controller" with "Virtualized Controller Architecture 2.0" really seems to be a Marvell 88SE9485 part, with OCZ firmware/BIOS. Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021] Should work on: - OCZ RevoDrive3 (2x SandForce 2281) - OCZ RevoDrive3 X2 (4x SandForce 2281) - OCZ zDrive R4 CM84 (4x SandForce 2281) - OCZ zDrive R4 CM88 (8x SandForce 2281) - OCZ zDrive R4 RM84 (4x SandForce 2582) - OCZ zDrive R4 RM88 (8x SandForce 2582) All of this because a friend recently bought a OCZ RevoDrive3 and was bitten by the lack of Linux support. Notes from testing: ------------------- - SMART works. - VPD Device Identification is "OCZ-REVODRIVE3" - Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP, with deterministic (non-zero) read after TRIM, but I'm not sure if it works 100% in my testing. - Some of the tuning in the firmware seems to ensure much better performance when in a RAID0 setup than using the two devices seperately. I have not tested booting from the SSD, because all of this was developed and tested remotely from the actual hardware. Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Thanks-To: Gordon Pritchard <gordp@sfu.ca> Acked-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage
Controller" with "Virtualized Controller Architecture 2.0" really seems
to be a Marvell 88SE9485 part, with OCZ firmware/BIOS.

Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021]

Should work on:
- OCZ RevoDrive3 (2x SandForce 2281)
- OCZ RevoDrive3 X2 (4x SandForce 2281)
- OCZ zDrive R4 CM84 (4x SandForce 2281)
- OCZ zDrive R4 CM88 (8x SandForce 2281)
- OCZ zDrive R4 RM84 (4x SandForce 2582)
- OCZ zDrive R4 RM88 (8x SandForce 2582)

All of this because a friend recently bought a OCZ RevoDrive3 and was
bitten by the lack of Linux support.

Notes from testing:
-------------------
- SMART works.
- VPD Device Identification is "OCZ-REVODRIVE3"
- Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP,
  with deterministic (non-zero) read after TRIM, but I'm not sure if it
  works 100% in my testing.
- Some of the tuning in the firmware seems to ensure much better
  performance when in a RAID0 setup than using the two devices
  seperately.

I have not tested booting from the SSD, because all of this was
developed and tested remotely from the actual hardware.

Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Thanks-To: Gordon Pritchard <gordp@sfu.ca>
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6 2011-10-28T23:44:18+00:00 Linus Torvalds torvalds@linux-foundation.org 2011-10-28T23:44:18+00:00 ec7ae517537ae5c7b0b2cd7f562dfa3e7a05b954 * git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits) [SCSI] qla4xxx: export address/port of connection (fix udev disk names) [SCSI] ipr: Fix BUG on adapter dump timeout [SCSI] megaraid_sas: Fix instance access in megasas_reset_timer [SCSI] hpsa: change confusing message to be more clear [SCSI] iscsi class: fix vlan configuration [SCSI] qla4xxx: fix data alignment and use nl helpers [SCSI] iscsi class: fix link local mispelling [SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA [SCSI] aacraid: use lower snprintf() limit [SCSI] lpfc 8.3.27: Change driver version to 8.3.27 [SCSI] lpfc 8.3.27: T10 additions for SLI4 [SCSI] lpfc 8.3.27: Fix queue allocation failure recovery [SCSI] lpfc 8.3.27: Change algorithm for getting physical port name [SCSI] lpfc 8.3.27: Changed worst case mailbox timeout [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes [SCSI] megaraid_sas: Changelog and version update [SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic [SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support [SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers [SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts ... 
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
  [SCSI] qla4xxx: export address/port of connection (fix udev disk names)
  [SCSI] ipr: Fix BUG on adapter dump timeout
  [SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
  [SCSI] hpsa: change confusing message to be more clear
  [SCSI] iscsi class: fix vlan configuration
  [SCSI] qla4xxx: fix data alignment and use nl helpers
  [SCSI] iscsi class: fix link local mispelling
  [SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
  [SCSI] aacraid: use lower snprintf() limit
  [SCSI] lpfc 8.3.27: Change driver version to 8.3.27
  [SCSI] lpfc 8.3.27: T10 additions for SLI4
  [SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
  [SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
  [SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
  [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
  [SCSI] megaraid_sas: Changelog and version update
  [SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
  [SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
  [SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
  [SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
  ...
[SCSI] isci: export phy events via ->lldd_control_phy() 2011-10-02T18:24:26+00:00 Dan Williams dan.j.williams@intel.com 2011-09-29T01:48:02+00:00 ac013ed1cb7b1b36113548ce83881a1b5f757b58 Allow the sas-transport-class to update events for local phys via a new PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that are not prepared for new enum phy_func values, and unify ->lldd_control_phy() error codes. These are the SAS defined phy events that are reported in a smp-report-phy-error-log command: * /sys/class/sas_phy/<phyX>/invalid_dword_count * /sys/class/sas_phy/<phyX>/running_disparity_error_count * /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count * /sys/class/sas_phy/<phyX>/phy_reset_problem_count Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy().  Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.

These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
 * /sys/class/sas_phy/<phyX>/invalid_dword_count
 * /sys/class/sas_phy/<phyX>/running_disparity_error_count
 * /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
 * /sys/class/sas_phy/<phyX>/phy_reset_problem_count

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mvsas: update driver version 2011-10-02T18:18:24+00:00 Xiangliang Yu yuxiangl@marvell.com 2011-09-29T07:35:38+00:00 4f3f812dd3b638d0c92661122dcccd6aaef66bfb This will synchronize the version string with internal driver. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
This will synchronize the version string with internal driver.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mvsas: fixed SMP request watchdog timeout issue. 2011-10-02T18:18:01+00:00 Xiangliang Yu yuxiangl@marvell.com 2011-09-29T07:35:15+00:00 40d3921f1dd4e1e53e10f064f0adf056f6e0f71a set SMP link timeout value to maximum. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
set SMP link timeout value to maximum.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mvsas: expander write performance enhancement 2011-10-02T18:17:27+00:00 Xiangliang Yu yuxiangl@marvell.com 2011-09-29T07:34:55+00:00 3a4b7efe7fa8ce3822f6139cddce4bae24c9ffe6 with 1 expander, connect 8 HDD, the write performance will be improved by 80%. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
with 1 expander, connect 8 HDD, the write performance will be
improved by 80%.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mvsas: change SL mode0 register value 2011-10-02T18:15:04+00:00 Xiangliang Yu yuxiangl@marvell.com 2011-09-29T07:34:32+00:00 aa117dd14372e1b0bed651af2db1be670b595032 -- change connection behavior -- set bit8 to 1 for performance tuning -- set bit0 to 0 to enable retry for no_dest reject case. Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
-- change connection behavior
-- set bit8 to 1 for performance tuning
-- set bit0 to 0 to enable retry for no_dest reject case.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mvsas: fixed wrong destination when hiting NAK for command frame 2011-10-02T18:14:00+00:00 Xiangliang Yu yuxiangl@marvell.com 2011-09-29T07:34:11+00:00 07f098e6f4a9a488605d6a3a13ce2805023a0384 disable non data frame retry Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> 
disable non data frame retry

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>