linux-toradex.git/drivers/scsi/scsi_lib.c, branch v3.12-rc2

Merge branch 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2013-09-04T01:19:53+00:00

Pull libata changes from Tejun Heo:
 "Two interesting changes.

   - libata acpi handling has been restructured so that the association
     between ata devices and ACPI handles are less convoluted.  This
     change shouldn't change visible behavior.

   - Queued TRIM support, which enables sending TRIM to the device
     without draining in-flight RW commands, is added.  Currently only
     enabled for ahci (and likely to stay that way for the foreseeable
     future).

  Other changes are driver-specific updates / fixes"

* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: bugfix: Remove __le32 in ata_tf_to_fis()
  libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
  libata: Add support for queued DSM TRIM
  libata: Add support for SEND/RECEIVE FPDMA QUEUED
  libata: Add H2D FIS "auxiliary" port flag
  libata: Populate host-to-device FIS "auxiliary" field
  ata: acpi: rework the ata acpi bind support
  sata, highbank: send extra clock cycles in SGPIO patterns
  sata, highbank: set tx_atten override bits
  devicetree: create a separate binding description for sata_highbank
  drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
  sata highbank: enable 64-bit DMA mask when using LPAE
  ata: pata_samsung_cf: add missing __iomem annotation
  ata: pata_arasan: Staticize local symbols
  sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
  ata: use dev_get_platdata()
  sata_mv: Remove unneeded forward declaration
  libata: acpi: remove dead code for ata_acpi_(un)bind
  libata: move 'struct ata_taskfile' and friends from ata.h to libata.h

[SCSI] Generate uevents on certain unit attention codes

2013-08-26T14:52:27+00:00

Generate a uevent when the following Unit Attention ASC/ASCQ
codes are received:

    2A/01  MODE PARAMETERS CHANGED
    2A/09  CAPACITY DATA HAS CHANGED
    38/07  THIN PROVISIONING SOFT THRESHOLD REACHED
    3F/03  INQUIRY DATA HAS CHANGED
    3F/0E  REPORTED LUNS DATA HAS CHANGED

Log kernel messages when the following Unit Attention ASC/ASCQ
codes are received that are not as specific as those above:

    2A/xx  PARAMETERS CHANGED
    3F/xx  TARGET OPERATING CONDITIONS HAVE CHANGED

Added logic to set expecting_lun_change for other LUNs on the target
after REPORTED LUNS DATA HAS CHANGED is received, so that duplicate
uevents are not generated, and clear expecting_lun_change when a
REPORT LUNS command completes, in accordance with the SPC-3
specification regarding reporting of the 3F 0E ASC/ASCQ UA.

[jejb: remove SPC3 test in scsi_report_lun_change and some docbook fixes and
       unused variable fix, both reported by Fengguang Wu]
Signed-off-by: Ewan D. Milne 
Signed-off-by: James Bottomley

[SCSI] Return ENODATA on medium error

2013-08-23T16:54:53+00:00

When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.

[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke 
Signed-off-by: James Bottomley

[SCSI] return ENOSPC on thin provisioning failure

2013-08-23T16:43:54+00:00

When the thin provisioning hard threshold is reached we
should return ENOSPC to inform upper layers about this fact.

Signed-off-by: Hannes Reinecke 
Signed-off-by: James Bottomley

[SCSI] Document enhanced error codes

2013-08-23T16:31:59+00:00

Document the various error codes returned on I/O failure.

Signed-off-by: Hannes Reinecke 
Signed-off-by: James Bottomley

ata: acpi: rework the ata acpi bind support

2013-08-23T16:09:23+00:00

Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
  while SCSI devices are not created yet. So each time ACPI handle is
  needed, instead of retrieving the handle by ACPI_HANDLE macro,
  a namespace scan is performed to find the handle for the corresponding
  ATA device. This is inefficient, and also expose a restriction on
  calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
  time doesn't bring us any benefit. All ACPI handlings are still done
  in ATA module, not in SCSI.

Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.

Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.

Signed-off-by: Aaron Lu 
Tested-by: Dirk Griesbach 
Signed-off-by: Tejun Heo

[SCSI] enable destruction of blocked devices which fail LUN scanning

2013-07-09T11:14:09+00:00

If something goes wrong during LUN scanning, e.g. a transport layer
failure occurs, then __scsi_remove_device() can get invoked by the
LUN scanning code for a SCSI device in state SDEV_CREATED_BLOCK and
before the SCSI device has been added to sysfs (is_visible == 0).
Make sure that even in this case the transition into state SDEV_DEL
occurs. This avoids that __scsi_remove_device() can get invoked a
second time by scsi_forget_host() if this last function is invoked
from another thread than the thread that performs LUN scanning.

Signed-off-by: Bart Van Assche 
Signed-off-by: James Bottomley

[SCSI] Fix race between starved list and device removal

2013-07-09T11:14:08+00:00

scsi_run_queue() examines all SCSI devices that are present on
the starved list. Since scsi_run_queue() unlocks the SCSI host
lock a SCSI device can get removed after it has been removed
from the starved list and before its queue is run. Protect
against that race condition by holding a reference on the
queue while running it.

Reported-by: Chanho Min 
Reviewed-by: Bart Van Assche 
Signed-off-by: James Bottomley

[SCSI] sd: use REQ_PM in sd's runtime suspend operation

2013-05-06T19:48:17+00:00

With the introduction of REQ_PM, modify sd's runtime suspend operation
functions to use that flag so that the operations to put the device into
runtime suspended state(i.e. sync cache and stop device) will not affect
its runtime PM status.

Signed-off-by: Lin Ming 
Signed-off-by: Aaron Lu 
Acked-by: Alan Stern 
Signed-off-by: James Bottomley

ACPI / glue: Add .match() callback to struct acpi_bus_type

2013-03-04T13:23:40+00:00

USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.

What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.

To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.

Signed-off-by: Rafael J. Wysocki 
Acked-by: Greg Kroah-Hartman 
Acked-by: Yinghai Lu 
Acked-by: Jeff Garzik