linux-toradex.git/drivers/scsi/st.c, branch v6.12-rc1 Linux kernel for Apalis and Colibri modules scsi: st: Fix input/output error on empty drive reset 2024-09-13T00:07:11+00:00 Rafael Rocha rrochavi@fnal.gov 2024-09-05T17:39:21+00:00 3d882cca73be830549833517ddccb3ac4668c04e A previous change was introduced to prevent data loss during a power-on reset when a tape is present inside the drive. This commit set the "pos_unknown" flag to true to avoid operations that could compromise data by performing actions from an untracked position. The relevant change is commit 9604eea5bd3a ("scsi: st: Add third party poweron reset handling") As a consequence of this change, a new issue has surfaced: the driver now returns an "Input/output error" even for empty drives when the drive, host, or bus is reset. This issue stems from the "flush_buffer" function, which first checks whether the "pos_unknown" flag is set. If the flag is set, the user will encounter an "Input/output error" until the tape position is known again. This behavior differs from the previous implementation, where empty drives were not affected at system start up time, allowing tape software to send commands to the driver to retrieve the drive's status and other information. The current behavior prioritizes the "pos_unknown" flag over the "ST_NO_TAPE" status, leading to issues for software that detects drives during system startup. This software will receive an "Input/output error" until a tape is loaded and its position is known. To resolve this, the "ST_NO_TAPE" status should take priority when the drive is empty, allowing communication with the drive following a power-on reset. At the same time, the change should continue to protect data by maintaining the "pos_unknown" flag when the drive contains a tape and its position is unknown. Signed-off-by: Rafael Rocha <rrochavi@fnal.gov> Link: https://lore.kernel.org/r/20240905173921.10944-1-rrochavi@fnal.gov Fixes: 9604eea5bd3a ("scsi: st: Add third party poweron reset handling") Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> 
A previous change was introduced to prevent data loss during a power-on
reset when a tape is present inside the drive. This commit set the
"pos_unknown" flag to true to avoid operations that could compromise data
by performing actions from an untracked position. The relevant change is
commit 9604eea5bd3a ("scsi: st: Add third party poweron reset handling")

As a consequence of this change, a new issue has surfaced: the driver now
returns an "Input/output error" even for empty drives when the drive, host,
or bus is reset. This issue stems from the "flush_buffer" function, which
first checks whether the "pos_unknown" flag is set. If the flag is set, the
user will encounter an "Input/output error" until the tape position is
known again. This behavior differs from the previous implementation, where
empty drives were not affected at system start up time, allowing tape
software to send commands to the driver to retrieve the drive's status and
other information.

The current behavior prioritizes the "pos_unknown" flag over the
"ST_NO_TAPE" status, leading to issues for software that detects drives
during system startup. This software will receive an "Input/output error"
until a tape is loaded and its position is known.

To resolve this, the "ST_NO_TAPE" status should take priority when the
drive is empty, allowing communication with the drive following a power-on
reset. At the same time, the change should continue to protect data by
maintaining the "pos_unknown" flag when the drive contains a tape and its
position is unknown.

Signed-off-by: Rafael Rocha <rrochavi@fnal.gov>
Link: https://lore.kernel.org/r/20240905173921.10944-1-rrochavi@fnal.gov
Fixes: 9604eea5bd3a ("scsi: st: Add third party poweron reset handling")
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: st: Drop driver owner initialization 2024-04-06T00:58:25+00:00 Krzysztof Kozlowski krzysztof.kozlowski@linaro.org 2024-03-28T20:45:49+00:00 2ee2d99fe4498d786e6773687bddba24c6684e6e Core in scsi_register_driver() already sets the .owner, so driver does not need to. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-5-c86cb4f6e91c@linaro.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> 
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-5-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: st: Make st_sysfs_class constant 2024-03-10T22:15:49+00:00 Ricardo B. Marliere ricardo@marliere.net 2024-03-02T16:47:26+00:00 0822853d658bbfa93bb16716ab10819788ad0550 Since commit 43a7206b0963 ("driver core: class: make class_register() take a const *"), the driver core allows for struct class to be in read-only memory, so move the st_sysfs_class structure to be declared at build time placing it into read-only memory, instead of having to be dynamically allocated at boot time. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net> Link: https://lore.kernel.org/r/20240302-class_cleanup-scsi-v1-5-b9096b990e27@marliere.net Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> 
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the st_sysfs_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240302-class_cleanup-scsi-v1-5-b9096b990e27@marliere.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: st: Add third party poweron reset handling 2023-08-25T02:16:28+00:00 John Meneghini jmeneghi@redhat.com 2023-08-22T18:14:12+00:00 9604eea5bd3ae1fa3c098294f4fc29ad687141ea Many tape devices will automatically rewind following a poweron/reset. This can result in data loss as other operations in the driver can write to the tape when the position is unknown. E.g. MTEOM can write a filemark at the beginning of the tape. This patch adds code to detect poweron/reset unit attentions and prevents the driver from writing to the tape when the position could be unknown. Customer reported problem description: We have experienced an issue with the SCSI tape driver (st) which has led to data loss for us on two separate occasions in production, as well as in a third case in which we were able to reproduce the failure in our test environment. The tape device involved is an Amazon Tape Gateway, a virtual tape library (VTL) appliance which presents as a series of iSCSI targets (multiple tape drives and a changer) and is backed by storage in Amazon S3. The problem is a general one and not limited to any particular SCSI transport or tape device, though the nature of both iSCSI and the VTL make data loss somewhat more likely with this combination than with a physical tape drive. The observed behavior occurs when an error causes the VTL tape gateway process (on the appliance) to crash and restart. This interrupts the iSCSI TCP connections and, when it occurs during a write, causes the write to fail with EIO. However, we then find that the virtual tape in question is now completely blank. We raised this issue with AWS support, thinking this must be a bug in the VTL appliance, but that turns out not to be the case. Per AWS support, when the gateway crashes in this manner, its notion of the current tape position is reset to the beginning of the tape. It also sets a unit attention condition, such that the next request results in a CHECK CONDITION status with sense key UNIT ATTENTION and asc/ascq indicating a device reset. According to their logs the next command being sent is WRITE FILEMARK, which results in writing an FM at the beginning of the tape, effectively discarding its contents. In fact, once the write fails with EIO, our software attempts to recover by rewinding and repositioning the tape, then resuming operation. If this fails, it attempts to rewind and reposition again, write a marker at the end of the tape, and then unmount. It does not under any circumstances write either data or filemarks without having successfully positioned the tape to a known point. What actually happens is that, since the last operation was a write, the kernel executes an implied MTWEOF operation (which translate to a Write Filemarks command) before the rewind that was actually requested. This seems not entirely unreasonable, provided the tape position is known. However, once this request fails (due to the unit attention condition), our next rewind attempt also triggers an implied MTWEOF, which does _not_ fail (the unit attention condition persists only until the initiator has been notified); this is the command that unexpectedly erases the tape. Our analysis is that the st driver is in fact completely ignoring the UNIT ATTENTION and associated reset notification from the device. This is not a condition that can be detected in the transport or mid-layer, as it occurs entirely within the target and is reported only via the UNIT ATTENTION sense key. The upper driver (i.e. st) needs to detect this indication and reset its internal model of the device to an unknown state. Suggested-by: Jeffrey Hutzelman <jhutz@cmu.edu> Signed-off-by: John Meneghini <jmeneghi@redhat.com> Link: https://lore.kernel.org/r/20230822181413.1210647-1-jmeneghi@redhat.com Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> 
Many tape devices will automatically rewind following a poweron/reset.
This can result in data loss as other operations in the driver can write to
the tape when the position is unknown. E.g. MTEOM can write a filemark at
the beginning of the tape. This patch adds code to detect poweron/reset
unit attentions and prevents the driver from writing to the tape when the
position could be unknown.

Customer reported problem description:

We have experienced an issue with the SCSI tape driver (st) which has led
to data loss for us on two separate occasions in production, as well as in
a third case in which we were able to reproduce the failure in our test
environment.

The tape device involved is an Amazon Tape Gateway, a virtual tape library
(VTL) appliance which presents as a series of iSCSI targets (multiple tape
drives and a changer) and is backed by storage in Amazon S3. The problem is
a general one and not limited to any particular SCSI transport or tape
device, though the nature of both iSCSI and the VTL make data loss somewhat
more likely with this combination than with a physical tape drive.

The observed behavior occurs when an error causes the VTL tape gateway
process (on the appliance) to crash and restart. This interrupts the iSCSI
TCP connections and, when it occurs during a write, causes the write to
fail with EIO. However, we then find that the virtual tape in question is
now completely blank. We raised this issue with AWS support, thinking this
must be a bug in the VTL appliance, but that turns out not to be the case.

Per AWS support, when the gateway crashes in this manner, its notion of the
current tape position is reset to the beginning of the tape. It also sets a
unit attention condition, such that the next request results in a CHECK
CONDITION status with sense key UNIT ATTENTION and asc/ascq indicating a
device reset. According to their logs the next command being sent is WRITE
FILEMARK, which results in writing an FM at the beginning of the tape,
effectively discarding its contents.

In fact, once the write fails with EIO, our software attempts to recover by
rewinding and repositioning the tape, then resuming operation. If this
fails, it attempts to rewind and reposition again, write a marker at the
end of the tape, and then unmount. It does not under any circumstances
write either data or filemarks without having successfully positioned the
tape to a known point.

What actually happens is that, since the last operation was a write, the
kernel executes an implied MTWEOF operation (which translate to a Write
Filemarks command) before the rewind that was actually requested. This
seems not entirely unreasonable, provided the tape position is known.
However, once this request fails (due to the unit attention condition), our
next rewind attempt also triggers an implied MTWEOF, which does _not_ fail
(the unit attention condition persists only until the initiator has been
notified); this is the command that unexpectedly erases the tape.

Our analysis is that the st driver is in fact completely ignoring the UNIT
ATTENTION and associated reset notification from the device. This is not a
condition that can be detected in the transport or mid-layer, as it occurs
entirely within the target and is reported only via the UNIT ATTENTION
sense key. The upper driver (i.e. st) needs to detect this indication and
reset its internal model of the device to an unknown state.

Suggested-by: Jeffrey Hutzelman <jhutz@cmu.edu>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Link: https://lore.kernel.org/r/20230822181413.1210647-1-jmeneghi@redhat.com
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: replace the fmode_t argument to scsi_ioctl with a simple bool 2023-06-12T14:04:04+00:00 Christoph Hellwig hch@lst.de 2023-06-08T11:02:47+00:00 2e80089c18241699c41d0af0669cb93844ff0dc1 Instead of passing a fmode_t and only checking it for FMODE_WRITE, pass a bool open_for_write to prepare for callers that won't have the fmode_t. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Acked-by: Christian Brauner <brauner@kernel.org> Link: https://lore.kernel.org/r/20230608110258.189493-20-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> 
Instead of passing a fmode_t and only checking it for FMODE_WRITE, pass
a bool open_for_write to prepare for callers that won't have the fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-20-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi 2022-10-07T19:33:18+00:00 Linus Torvalds torvalds@linux-foundation.org 2022-10-07T19:33:18+00:00 62e6e5940c0c09433efa52d0fa9a11623a4704b2 Pull SCSI updates from James Bottomley: "Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr, mpt3sas, target). The biggest change (from my biased viewpoint) being that the mpi3mr now attached to the SAS transport class, making it the first fusion type device to do so. Beyond the usual bug fixing and security class reworks, there aren't a huge number of core changes" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits) scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername() scsi: mpi3mr: Remove unnecessary cast scsi: stex: Properly zero out the passthrough command structure scsi: mpi3mr: Update driver version to 8.2.0.3.0 scsi: mpi3mr: Fix scheduling while atomic type bug scsi: mpi3mr: Scan the devices during resume time scsi: mpi3mr: Free enclosure objects during driver unload scsi: mpi3mr: Handle 0xF003 Fault Code scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels scsi: mpi3mr: Support new power management framework scsi: mpi3mr: Update mpi3 header files scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use" scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use" scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO scsi: core: Add I/O timeout count for SCSI device scsi: qedf: Populate sysfs attributes for vport scsi: pm8001: Replace one-element array with flexible-array member scsi: 3w-xxxx: Replace one-element array with flexible-array member scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command() ... 
Pull SCSI updates from James Bottomley:
 "Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
  mpt3sas, target). The biggest change (from my biased viewpoint) being
  that the mpi3mr now attached to the SAS transport class, making it the
  first fusion type device to do so.

  Beyond the usual bug fixing and security class reworks, there aren't a
  huge number of core changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
  scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
  scsi: mpi3mr: Remove unnecessary cast
  scsi: stex: Properly zero out the passthrough command structure
  scsi: mpi3mr: Update driver version to 8.2.0.3.0
  scsi: mpi3mr: Fix scheduling while atomic type bug
  scsi: mpi3mr: Scan the devices during resume time
  scsi: mpi3mr: Free enclosure objects during driver unload
  scsi: mpi3mr: Handle 0xF003 Fault Code
  scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
  scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
  scsi: mpi3mr: Support new power management framework
  scsi: mpi3mr: Update mpi3 header files
  scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
  scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
  scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
  scsi: core: Add I/O timeout count for SCSI device
  scsi: qedf: Populate sysfs attributes for vport
  scsi: pm8001: Replace one-element array with flexible-array member
  scsi: 3w-xxxx: Replace one-element array with flexible-array member
  scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
  ...
block: change request end_io handler to pass back a return value 2022-09-30T13:49:09+00:00 Jens Axboe axboe@kernel.dk 2022-09-21T21:19:54+00:00 de671d6116b5210097cd6fbb877bac92536f265b Everything is just converted to returning RQ_END_IO_NONE, and there should be no functional changes with this patch. In preparation for allowing the end_io handler to pass ownership back to the block layer, rather than retain ownership of the request. Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> 
Everything is just converted to returning RQ_END_IO_NONE, and there
should be no functional changes with this patch.

In preparation for allowing the end_io handler to pass ownership back
to the block layer, rather than retain ownership of the request.

Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
scsi: st: Remove redundant variable pointer stp 2022-09-01T03:39:57+00:00 Colin Ian King colin.i.king@gmail.com 2022-08-05T11:56:52+00:00 f0ee639adb78753377da3d125d7d72531026bca1 Variable stp is assigned a value that is never read, the assignment and the variable stp are redundant and can be removed. Cleans up clang scan build warning: drivers/scsi/st.c:4253:7: warning: Although the value stored to 'stp' is used in the enclosing expression, the value is never actually read from 'stp' [deadcode.DeadStores] Link: https://lore.kernel.org/r/20220805115652.2340991-1-colin.i.king@gmail.com Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> 
Variable stp is assigned a value that is never read, the assignment and the
variable stp are redundant and can be removed.

Cleans up clang scan build warning:

drivers/scsi/st.c:4253:7: warning: Although the value stored to 'stp'
is used in the enclosing expression, the value is never actually
read from 'stp' [deadcode.DeadStores]

Link: https://lore.kernel.org/r/20220805115652.2340991-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk-mq: remove the done argument to blk_execute_rq_nowait 2022-05-28T12:15:27+00:00 Christoph Hellwig hch@lst.de 2022-05-24T12:15:30+00:00 e2e530867245d051dc7800b0d07193b3e581f5b9 Let the caller set it together with the end_io_data instead of passing a pointless argument. Note the the target code did in fact already set it and then just overrode it again by calling blk_execute_rq_nowait. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Kanchan Joshi <joshi.k@samsung.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Link: https://lore.kernel.org/r/20220524121530.943123-4-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> 
Let the caller set it together with the end_io_data instead of passing
a pointless argument.  Note the the target code did in fact already
set it and then just overrode it again by calling blk_execute_rq_nowait.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220524121530.943123-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi 2022-03-25T02:37:53+00:00 Linus Torvalds torvalds@linux-foundation.org 2022-03-25T02:37:53+00:00 6f2689a7662809ff39f2b24e452d11569c21ea2f Pull SCSI updates from James Bottomley: "This series consists of the usual driver updates (qla2xxx, pm8001, libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates and bug fixes. The high blast radius core update is the removal of write same, which affects block and several non-SCSI devices. The other big change, which is more local, is the removal of the SCSI pointer" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits) scsi: scsi_ioctl: Drop needless assignment in sg_io() scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn() scsi: lpfc: Copyright updates for 14.2.0.0 patches scsi: lpfc: Update lpfc version to 14.2.0.0 scsi: lpfc: SLI path split: Refactor BSG paths scsi: lpfc: SLI path split: Refactor Abort paths scsi: lpfc: SLI path split: Refactor SCSI paths scsi: lpfc: SLI path split: Refactor CT paths scsi: lpfc: SLI path split: Refactor misc ELS paths scsi: lpfc: SLI path split: Refactor VMID paths scsi: lpfc: SLI path split: Refactor FDISC paths scsi: lpfc: SLI path split: Refactor LS_RJT paths scsi: lpfc: SLI path split: Refactor LS_ACC paths scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4 scsi: lpfc: SLI path split: Refactor lpfc_iocbq scsi: lpfc: Use kcalloc() ... 
Pull SCSI updates from James Bottomley:
 "This series consists of the usual driver updates (qla2xxx, pm8001,
  libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
  and bug fixes.

  The high blast radius core update is the removal of write same, which
  affects block and several non-SCSI devices. The other big change,
  which is more local, is the removal of the SCSI pointer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
  scsi: scsi_ioctl: Drop needless assignment in sg_io()
  scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
  scsi: lpfc: Copyright updates for 14.2.0.0 patches
  scsi: lpfc: Update lpfc version to 14.2.0.0
  scsi: lpfc: SLI path split: Refactor BSG paths
  scsi: lpfc: SLI path split: Refactor Abort paths
  scsi: lpfc: SLI path split: Refactor SCSI paths
  scsi: lpfc: SLI path split: Refactor CT paths
  scsi: lpfc: SLI path split: Refactor misc ELS paths
  scsi: lpfc: SLI path split: Refactor VMID paths
  scsi: lpfc: SLI path split: Refactor FDISC paths
  scsi: lpfc: SLI path split: Refactor LS_RJT paths
  scsi: lpfc: SLI path split: Refactor LS_ACC paths
  scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
  scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
  scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
  scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
  scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
  scsi: lpfc: SLI path split: Refactor lpfc_iocbq
  scsi: lpfc: Use kcalloc()
  ...