Pull ARM SoC driver updates from Arnd Bergmann:
 "As usual, there are lots of minor driver changes across SoC platforms
  from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
  These usually add support for additional chip variations in existing
  drivers, but also add features or bugfixes.

  The SCMI firmware subsystem gains a unified raw userspace interface
  through debugfs, which can be used for validation purposes.

  Newly added drivers include:

   - New power management drivers for StarFive JH7110, Allwinner D1 and
     Renesas RZ/V2M

   - A driver for Qualcomm battery and power supply status

   - A SoC device driver for identifying Nuvoton WPCM450 chips

   - A regulator coupler driver for Mediatek MT81xxv"

* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  power: supply: Introduce Qualcomm PMIC GLINK power supply
  soc: apple: rtkit: Do not copy the reg state structure to the stack
  soc: sunxi: SUN20I_PPU should depend on PM
  memory: renesas-rpc-if: Remove redundant division of dummy
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  ...

Pull driver core updates from Greg KH:
 "Here is the large set of driver core changes for 6.3-rc1.

  There's a lot of changes this development cycle, most of the work
  falls into two different categories:

   - fw_devlink fixes and updates. This has gone through numerous review
     cycles and lots of review and testing by lots of different devices.
     Hopefully all should be good now, and Saravana will be keeping a
     watch for any potential regression on odd embedded systems.

   - driver core changes to work to make struct bus_type able to be
     moved into read-only memory (i.e. const) The recent work with Rust
     has pointed out a number of areas in the driver core where we are
     passing around and working with structures that really do not have
     to be dynamic at all, and they should be able to be read-only
     making things safer overall. This is the contuation of that work
     (started last release with kobject changes) in moving struct
     bus_type to be constant. We didn't quite make it for this release,
     but the remaining patches will be finished up for the release after
     this one, but the groundwork has been laid for this effort.

  Other than that we have in here:

   - debugfs memory leak fixes in some subsystems

   - error path cleanups and fixes for some never-able-to-be-hit
     codepaths.

   - cacheinfo rework and fixes

   - Other tiny fixes, full details are in the shortlog

  All of these have been in linux-next for a while with no reported
  problems"

[ Geert Uytterhoeven points out that that last sentence isn't true, and
  that there's a pending report that has a fix that is queued up - Linus ]

* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
  debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
  OPP: fix error checking in opp_migrate_dentry()
  debugfs: update comment of debugfs_rename()
  i3c: fix device.h kernel-doc warnings
  dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
  driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
  Revert "driver core: add error handling for devtmpfs_create_node()"
  Revert "devtmpfs: add debug info to handle()"
  Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
  driver core: cpu: don't hand-override the uevent bus_type callback.
  devtmpfs: remove return value of devtmpfs_delete_node()
  devtmpfs: add debug info to handle()
  driver core: add error handling for devtmpfs_create_node()
  driver core: bus: update my copyright notice
  driver core: bus: add bus_get_dev_root() function
  driver core: bus: constify bus_unregister()
  driver core: bus: constify some internal functions
  driver core: bus: constify bus_get_kset()
  driver core: bus: constify bus_register/unregister_notifier()
  driver core: remove private pointer from struct bus_type
  ...

Pull tty / serial driver updates from Greg KH:
 "Here is the big set of serial and tty driver updates for 6.3-rc1.

  Once again, Jiri and Ilpo have done a number of core vt and tty/serial
  layer cleanups that were much needed and appreciated. Other than that,
  it's just a bunch of little tty/serial driver updates:

   - qcom-geni-serial driver updates

   - liteuart driver updates

   - hvcs driver cleanups

   - n_gsm updates and additions for new features

   - more 8250 device support added

   - fpga/dfl update and additions

   - imx serial driver updates

   - fsl_lpuart updates

   - other tiny fixes and updates for serial drivers

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
  tty: n_gsm: add keep alive support
  serial: imx: remove a redundant check
  dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
  soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
  tty: n_gsm: add TIOCMIWAIT support
  tty: n_gsm: add RING/CD control support
  tty: n_gsm: mark unusable ioctl structure fields accordingly
  serial: imx: get rid of registers shadowing
  serial: imx: refine local variables in rxint()
  serial: imx: stop using USR2 in FIFO reading loop
  serial: imx: remove redundant USR2 read from FIFO reading loop
  serial: imx: do not break from FIFO reading loop prematurely
  serial: imx: do not sysrq broken chars
  serial: imx: work-around for hardware RX flood
  serial: imx: factor-out common code to imx_uart_soft_reset()
  serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
  serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
  serial: 8250_pci1xxxx: Add driver for quad-uart support
  serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
  tty: pcn_uart: fix memory leak with using debugfs_lookup()
  ...

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

Pull hardening updates from Kees Cook:
 "Beyond some specific LoadPin, UBSAN, and fortify features, there are
  other fixes scattered around in various subsystems where maintainers
  were okay with me carrying them in my tree or were non-responsive but
  the patches were reviewed by others:

   - Replace 0-length and 1-element arrays with flexible arrays in
     various subsystems (Paulo Miguel Almeida, Stephen Rothwell, Kees
     Cook)

   - randstruct: Disable Clang 15 support (Eric Biggers)

   - GCC plugins: Drop -std=gnu++11 flag (Sam James)

   - strpbrk(): Refactor to use strchr() (Andy Shevchenko)

   - LoadPin LSM: Allow root filesystem switching when non-enforcing

   - fortify: Use dynamic object size hints when available

   - ext4: Fix CFI function prototype mismatch

   - Nouveau: Fix DP buffer size arguments

   - hisilicon: Wipe entire crypto DMA pool on error

   - coda: Fully allocate sig_inputArgs

   - UBSAN: Improve arm64 trap code reporting

   - copy_struct_from_user(): Add minimum bounds check on kernel buffer
     size"

* tag 'hardening-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  randstruct: disable Clang 15 support
  uaccess: Add minimum bounds check on kernel buffer size
  arm64: Support Clang UBSAN trap codes for better reporting
  coda: Avoid partial allocation of sig_inputArgs
  gcc-plugins: drop -std=gnu++11 to fix GCC 13 build
  lib/string: Use strchr() in strpbrk()
  crypto: hisilicon: Wipe entire pool on error
  net/i40e: Replace 0-length array with flexible array
  io_uring: Replace 0-length array with flexible array
  ext4: Fix function prototype mismatch for ext4_feat_ktype
  i915/gvt: Replace one-element array with flexible-array member
  drm/nouveau/disp: Fix nvif_outp_acquire_dp() argument size
  LoadPin: Allow filesystem switch when not enforcing
  LoadPin: Move pin reporting cleanly out of locking
  LoadPin: Refactor sysctl initialization
  LoadPin: Refactor read-only check into a helper
  ARM: ixp4xx: Replace 0-length arrays with flexible arrays
  fortify: Use __builtin_dynamic_object_size() when available
  rxrpc: replace zero-lenth array with DECLARE_FLEX_ARRAY() helper

Pull ARM SoC updates from Arnd Bergmann:
 "The majority of the changes are for the OMAP2 platform, mostly
  removing some dead code that got left behind from previous cleanups.

  Aside from that, there are very minor updates and correctness fixes
  for Zynq, i.MX, Samsung, Broadcom, AT91, ep93xx, and OMAP1"

* tag 'arm-soc-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
  dt-bindings: soc: samsung: exynos-pmu: allow phys as child
  ARM: imx: mach-imx6ul: add imx6ulz support
  ARM: imx: Call ida_simple_remove() for ida_simple_get
  arm64: drop redundant "ARMv8" from Kconfig option title
  ARM: ep93xx: Convert to use descriptors for GPIO LEDs
  ARM: s3c: fix s3c64xx_set_timer_source prototype
  ARM: OMAP2+: Fix spelling typos in comment
  ARM: OMAP2+: Remove unneeded #include <linux/pinctrl/machine.h>
  ARM: OMAP2+: Remove unneeded #include <linux/pinctrl/pinmux.h>
  ARM: OMAP1: call platform_device_put() in error case in omap1_dm_timer_init()
  ARM: BCM63xx: remove useless goto statement
  ARM: omap2: make functions static
  ARM: omap2: remove unused omap2_pm_init
  ARM: omap2: remove unused declarations
  ARM: omap2: remove unused functions
  ARM: omap2: smartreflex: remove on_init control
  ARM: omap2: remove APLL control
  ARM: omap2: simplify clock2xxx header
  ARM: omap2: remove unused omap_hwmod_reset.c
  ARM: omap2: remove unused headers
  ...

Pull ARM SoC boardfile updates from Arnd Bergmann
 "Unused boardfile removal for 6.3

  This is a follow-up to the deprecation of most of the old-style board
  files that was merged in linux-6.0, removing them for good.

  This branch is almost exclusively dead code removal based on those
  annotations. Some device driver removals went through separate
  subsystem trees, but the majority is in the same branch, in order to
  better handle dependencies between the patches and avoid breaking
  bisection.

  Unfortunately that leads to merge conflicts against other changes in
  the subsystem trees, but they should all be trivial to resolve by
  removing the files.

  See commit 7d0d3fa7339e ("Merge tag 'arm-boardfiles-6.0' of
  git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
  description of which machines were marked unused and are now removed.

  The only removals that got postponed are Terastation WXL (mv78xx0) and
  Jornada720 (StrongARM1100), which turned out to still have potential
  users"

* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
  mmc: omap: drop TPS65010 dependency
  ARM: pxa: restore mfp-pxa320.h
  usb: ohci-omap: avoid unused-variable warning
  ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
  ARM: s3c: remove obsolete s3c-cpu-freq header
  MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
  MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
  ARM: remove CONFIG_UNUSED_BOARD_FILES
  mfd: remove htc-pasic3 driver
  w1: remove ds1wm driver
  usb: remove ohci-tmio driver
  fbdev: remove w100fb driver
  fbdev: remove tmiofb driver
  mmc: remove tmio_mmc driver
  mfd: remove ucb1400 support
  mfd: remove toshiba tmio drivers
  rtc: remove v3020 driver
  power: remove pda_power supply driver
  ASoC: pxa: remove unused board support
  pcmcia: remove unused pxa/sa1100 drivers
  ...

The register state struct is 848 bytes, which ends up bloating the
apple_rtkit_crashlog_dump_regs stack frame beyond 1024 on some
32-bit platforms, triggering compile warnings.

This doesn't matter for 64BIT/ARM64, but there's also no good reason to
copy the structure to the stack in this case. We can use __packed to
avoid alignment issues, there are no double-read hazards, and this is a
fatal error path so performance does not matter.

Fixes: 22991d8d5725 ("soc: apple: rtkit: Add register dump decoding to crashlog")
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

More Qualcomm driver updates for 6.3

The qcom_scm.h file is moved into firmware/qcom, to avoid having any
Qualcomm-specific files directly in include/linux.

Support for PMIC GLINK is introduced, which on newer Qualcomm platforms
provides an interface to the firmware implementing battery management
and USB Type-C handling. Together with the base driver comes the custom
altmode support driver.

SMD RPM gains support for IPQ9574, and socinfo is extended with support
for revision 17 of the information format and soc_id for IPQ5332 and
IPQ8064 are added.

The qcom_stats  is changes not to fail when not all parts are
initialized.

* tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  soc: qcom: pmic_glink: Introduce base PMIC GLINK driver
  dt-bindings: soc: qcom: Introduce PMIC GLINK binding
  soc: qcom: dcc: Drop driver for now

Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Qualcomm driver updates for v6.3

This introduces a new driver for the Data Capture and Compare block,
which provides a mechanism for capturing hardware state (access MMIO
registers) either upon request of triggered automatically e.g. upon a
watchdog bite, for post mortem analysis.

The remote filesystem memory share driver gains support for having its
memory bound to more than a single VMID.

The SCM driver gains the minimal support needed to support a new
mechanism where secure world can put calls on hold and later request
them to be retried.

Support for the new SA8775P platform is added to rpmhpd, QDU1000 is
added to the SCM driver and a long list of platforms are added to the
socinfo driver. Support for socinfo data revision 16 is also introduced.

Lastly a driver to program the ramp controller in MSM8976 is introduced.

* tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
  firmware: qcom: scm: Add wait-queue handling logic
  dt-bindings: firmware: qcom,scm: Add optional interrupt
  Revert "dt-bindings: power: rpmpd: Add SM4250 support"
  Revert "soc: qcom: rpmpd: Add SM4250 support"
  soc: qcom: socinfo: Add a bunch of older SoCs
  dt-bindings: arm: qcom,ids: Add a bunch of older SoCs
  dt-bindings: arm: qcom,ids: Add QRD board ID
  soc: qcom: socinfo: Fix soc_id order
  dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
  dt-bindings: firmware: qcom: scm: Separate VMIDs from header to bindings
  soc: qcom: rmtfs: Optionally map RMTFS to more VMs
  dt-bindings: reserved-memory: rmtfs: Make qcom,vmid an array
  dt-bindings: firmware: scm: Add QDU1000/QRU1000 compatible
  dt-bindings: firmware: qcom,scm: narrow clocks and interconnects
  dt-bindings: firmware: qcom,scm: document MSM8226 clocks
  soc: qcom: ramp_controller: Make things static
  soc: qcom: rmphpd: add power domains for sa8775p
  dt-bindings: power: qcom,rpmpd: document sa8775p
  PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
  soc: qcom: dcc: rewrite description of dcc sysfs files
  ...

Link: https://lore.kernel.org/r/20230126163008.3676950-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>