linux-toradex.git/drivers/staging, branch v4.4.52

staging: comedi: dt282x: tidy up register bit defines

2017-01-12T10:22:50+00:00

commit f6b1160eb27f990cc1c48b67a5f83cb63115284e upstream.

Arnd Bergmann pointed out that gcc-6 warns about passing negative signed
integer into swab16() due to the macro expansion of 'outw'.

It appears that the register map constants are causing the warnings.
Actually, it might just be the (1 << 15) ones...

Convert all the constants as suggested by checkpatch.pl:
CHECK: Prefer using the BIT macro

The BIT() macro will make all the constants explicitly 'unsigned', which
helps to avoid the warning.

Fix the, unsused, DT2821_CHANCSR_PRESLA() macro. The "Present List
Address" (PRESLA) bits in the CHANCSR register are read only. This
define was meant to extract the bits from the read value.

Signed-off-by: H Hartley Sweeten 
Reported-by: Arnd Bergmann 
Reviewed-by: Ian Abbott 
Tested-by: Arnd Bergmann 
Signed-off-by: Greg Kroah-Hartman

staging: iio: ad7606: fix improper setting of oversampling pins

2017-01-12T10:22:48+00:00

commit b321a38d2407c7e425c54bc09be909a34e49f740 upstream.

The oversampling ratio is controlled using the oversampling pins,
OS [2:0] with OS2 being the MSB control bit, and OS0 the LSB control
bit.

The gpio connected to the OS2 pin is not being set correctly, only OS0
and OS1 pins are being set. Fix the typo to allow proper control of the
oversampling pins.

Signed-off-by: Eva Rachel Retuya 
Fixes: b9618c0 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4")
Acked-by: Lars-Peter Clausen 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

staging: comedi: ni_mio_common: fix E series ni_ai_insn_read() data

2017-01-09T07:07:44+00:00

commit 857a661020a2de3a0304edf33ad656abee100891 upstream.

Commit 0557344e2149 ("staging: comedi: ni_mio_common: fix local var for
32-bit read") changed the type of local variable `d` from `unsigned
short` to `unsigned int` to fix a bug introduced in
commit 9c340ac934db ("staging: comedi: ni_stc.h: add read/write
callbacks to struct ni_private") when reading AI data for NI PCI-6110
and PCI-6111 cards.  Unfortunately, other parts of the function rely on
the variable being `unsigned short` when an offset value in local
variable `signbits` is added to `d` before writing the value to the
`data` array:

			d += signbits;
		  	data[n] = d;

The `signbits` variable will be non-zero in bipolar mode, and is used to
convert the hardware's 2's complement, 16-bit numbers to Comedi's
straight binary sample format (with 0 representing the most negative
voltage).  This breaks because `d` is now 32 bits wide instead of 16
bits wide, so after the addition of `signbits`, `data[n]` ends up being
set to values above 65536 for negative voltages.  This affects all
supported "E series" cards except PCI-6143 (and PXI-6143). Fix it by
ANDing the value written to the `data[n]` with the mask 0xffff.

Fixes: 0557344e2149 ("staging: comedi: ni_mio_common: fix local var for 32-bit read")
Signed-off-by: Ian Abbott 
Signed-off-by: Greg Kroah-Hartman

staging: comedi: ni_mio_common: fix M Series ni_ai_insn_read() data mask

2017-01-09T07:07:44+00:00

commit 655c4d442d1213b617926cc6d54e2a9a793fb46b upstream.

For NI M Series cards, the Comedi `insn_read` handler for the AI
subdevice is broken due to ANDing the value read from the AI FIFO data
register with an incorrect mask.  The incorrect mask clears all but the
most significant bit of the sample data.  It should preserve all the
sample data bits.  Correct it.

Fixes: 817144ae7fda ("staging: comedi: ni_mio_common: remove unnecessary use of 'board->adbits'")
Signed-off-by: Ian Abbott 
Signed-off-by: Greg Kroah-Hartman

staging: nvec: remove managed resource from PS2 driver

2016-11-18T09:48:35+00:00

commit 68fae2f3df455f53d0dfe33483a49020b3b758f3 upstream.

This basicly reverts commit e534f3e9 (staging:nvec: Introduce the use of
the managed version of kzalloc). Serio struct should never by managed
because it is refcounted. Doing so will lead to a double free oops on module
remove.

Signed-off-by: Marc Dietrich 
Fixes: e534f3e9429f ("staging:nvec: Introduce the use of the managed version of kzalloc")
Signed-off-by: Greg Kroah-Hartman

Revert "staging: nvec: ps2: change serio type to passthrough"

2016-11-18T09:48:35+00:00

commit 17c1c9ba15b238ef79b51cf40d855c05b58d5934 upstream.

This reverts commit 36b30d6138f4677514aca35ab76c20c1604baaad.

This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.

Commit ec6184b1c717b8768122e25fe6d312f609cc1bb4 changed the way
auto-detection is performed on ports marked as pass through and made the
issue apparent.

A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).

Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.

Signed-off-by: Paul Fertser 
Acked-by: Marc Dietrich 
Fixes: 36b30d6138f4 ("staging: nvec: ps2: change serio type to passthrough")
Signed-off-by: Greg Kroah-Hartman

drivers: staging: nvec: remove bogus reset command for PS/2 interface

2016-11-18T09:48:35+00:00

commit d8f8a74d5fece355d2234e1731231d1aebc66b38 upstream.

This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.

To prevent this from happening just let every party do its part of the
job.

Signed-off-by: Paul Fertser 
Acked-by: Marc Dietrich 
Signed-off-by: Greg Kroah-Hartman

staging: iio: ad5933: avoid uninitialized variable in error case

2016-11-18T09:48:35+00:00

commit 34eee70a7b82b09dbda4cb453e0e21d460dae226 upstream.

The ad5933_i2c_read function returns an error code to indicate
whether it could read data or not. However ad5933_work() ignores
this return code and just accesses the data unconditionally,
which gets detected by gcc as a possible bug:

drivers/staging/iio/impedance-analyzer/ad5933.c: In function 'ad5933_work':
drivers/staging/iio/impedance-analyzer/ad5933.c:649:16: warning: 'status' may be used uninitialized in this function [-Wmaybe-uninitialized]

This adds minimal error handling so we only evaluate the
data if it was correctly read.

Link: https://patchwork.kernel.org/patch/8110281/
Signed-off-by: Arnd Bergmann 
Acked-by: Lars-Peter Clausen 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

staging: r8188eu: Fix scheduling while atomic splat

2016-10-31T10:14:00+00:00

commit 1335a9516d3d52f157ad87456efdd8dc9ae1747b upstream.

Commit fadbe0cd5292851608e2e01b91d9295fa287b9fe ("staging: rtl8188eu:
Remove rtw_zmalloc(), wrapper for kzalloc()") changed all allocation
calls to be GFP_KERNEL even though the original wrapper was testing
to determine if the caller was in atomic mode. Most of the mistakes
were corrected with commit 33dc85c3c667209c930b2dac5ccbc2a365e06b7a
("staging: r8188eu: Fix scheduling while atomic error introduced in
commit fadbe0cd"); however, two kzalloc calls were missed as the
call only happens when the driver is shutting down.

Fixes: fadbe0cd5292851608e2e01b91d9295fa287b9fe ("staging: rtl8188eu: Remove rtw_zmalloc(), wrapper for kzalloc()")
Signed-off-by: Larry Finger 
Cc: navin patidar 
Signed-off-by: Greg Kroah-Hartman

Staging: fbtft: Fix bug in fbtft-core

2016-10-07T13:23:47+00:00

commit fc1e2c8ea85e109acf09e74789e9b852f6eed251 upstream.

Commit 367e8560e8d7a62d96e9b1d644028a3816e04206 introduced a bug
in fbtft-core where fps is always 0, this is because variable
update_time is not assigned correctly.

Signed-off-by: Ksenija Stanojevic 
Fixes: 367e8560e8d7 ("Staging: fbtbt: Replace timespec with ktime_t")
Signed-off-by: Greg Kroah-Hartman