linux-toradex.git/drivers/tty/serial, branch v3.2.32 Linux kernel for Apalis and Colibri modules serial: pl011: handle corruption at high clock speeds 2012-10-17T02:49:02+00:00 Linus Walleij linus.walleij@linaro.org 2012-09-26T15:21:36+00:00 4ac206a50c319f692aab900408f949b04f8deab7 commit c5dd553b9fd069892c9e2de734f4f604e280fa7a upstream. This works around a few glitches in the ST version of the PL011 serial driver when using very high baud rates, as we do in the Ux500: 3, 3.25, 4 and 4.05 Mbps. Problem Observed/rootcause: When using high baud-rates, and the baudrate*8 is getting close to the provided clock frequency (so a division factor close to 1), when using bursts of characters (so they are abutted), then it seems as if there is not enough time to detect the beginning of the start-bit which is a timing reference for the entire character, and thus the sampling moment of character bits is moving towards the end of each bit, instead of the middle. Fix: Increase slightly the RX baud rate of the UART above the theoretical baudrate by 5%. This will definitely give more margin time to the UART_RX to correctly sample the data at the middle of the bit period. Also fix the ages old copy-paste error in the very stressed comment, it's referencing the registers used in the PL010 driver rather than the PL011 ones. Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com> Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com> Signed-off-by: Matthias Locher <matthias.locher@stericsson.com> Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com> Cc: Bibek Basu <bibek.basu@stericsson.com> Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit c5dd553b9fd069892c9e2de734f4f604e280fa7a upstream.

This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.

Problem Observed/rootcause:

When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.

Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.

Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.

Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
serial: set correct baud_base for EXSYS EX-41092 Dual 16950 2012-10-17T02:49:01+00:00 Flavio Leitner fbl@redhat.com 2012-09-22T00:04:34+00:00 96311cce7d8e427aad023c8eea6ba3a08b70e754 commit 26e8220adb0aec43b7acafa0f1431760eee28522 upstream. Apparently the same card model has two IDs, so this patch complements the commit 39aced68d664291db3324d0fcf0985ab5626aac2 adding the missing one. Signed-off-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 26e8220adb0aec43b7acafa0f1431760eee28522 upstream.

Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d664291db3324d0fcf0985ab5626aac2
adding the missing one.

Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pch_uart: Add eg20t_port lock field, avoid recursive spinlocks 2012-10-10T02:31:12+00:00 Darren Hart dvhart@linux.intel.com 2012-06-19T21:00:18+00:00 3f00d57fffdf2708689bd75780cb0eeee26eedea commit 2588aba002d14e938c2f56d299ecf3e7ce1302a5 upstream. pch_uart_interrupt() takes priv->port.lock which leads to two recursive spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one otherwise): pch_uart_interrupt spin_lock_irqsave(priv->port.lock, flags) case PCH_UART_IID_RDR_TO (data ready) handle_rx_to push_rx tty_port_tty_get spin_lock_irqsave(&port->lock, flags) <--- already hold this lock ... tty_flip_buffer_push ... flush_to_ldisc spin_lock_irqsave(&tty->buf.lock) spin_lock_irqsave(&tty->buf.lock) disc->ops->receive_buf(tty, char_buf) n_tty_receive_buf tty->ops->flush_chars() uart_flush_chars uart_start spin_lock_irqsave(&port->lock) <--- already hold this lock Avoid this by using a dedicated lock to protect the eg20t_port structure and IO access to its membase. This is more consistent with the 8250 driver. Ensure priv->lock is always take prior to priv->port.lock when taken at the same time. V2: Remove inadvertent whitespace change. V3: Account for oops_in_progress for the private lock in pch_console_write(). Note: Like the 8250 driver, if a printk is introduced anywhere inside the pch_console_write() critical section, the kernel will hang on a recursive spinlock on the private lock. The oops case is handled by using a trylock in the oops_in_progress case. Signed-off-by: Darren Hart <dvhart@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Feng Tang <feng.tang@intel.com> CC: Alexander Stein <alexander.stein@systec-electronic.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - Adjust context - Drop changes to pch_console_write()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2588aba002d14e938c2f56d299ecf3e7ce1302a5 upstream.

pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):

pch_uart_interrupt
  spin_lock_irqsave(priv->port.lock, flags)
  case PCH_UART_IID_RDR_TO (data ready)
  handle_rx_to
    push_rx
      tty_port_tty_get
        spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
        ...
      tty_flip_buffer_push
        ...
        flush_to_ldisc
          spin_lock_irqsave(&tty->buf.lock)
            spin_lock_irqsave(&tty->buf.lock)
            disc->ops->receive_buf(tty, char_buf)
              n_tty_receive_buf
                tty->ops->flush_chars()
                uart_flush_chars
                  uart_start
                    spin_lock_irqsave(&port->lock) <--- already hold this lock

Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver.  Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.

V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
    pch_console_write().

Note: Like the 8250 driver, if a printk is introduced anywhere inside
      the pch_console_write() critical section, the kernel will hang
      on a recursive spinlock on the private lock. The oops case is
      handled by using a trylock in the oops_in_progress case.

Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
 - Adjust context
 - Drop changes to pch_console_write()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tty: serial: imx: don't reinit clock in imx_setup_ufcr() 2012-09-19T14:05:14+00:00 Dirk Behme dirk.behme@de.bosch.com 2012-08-31T08:02:47+00:00 da75c41ed3cf1fc577b24dc87559bd32e27ebc8b commit 7be0670f7b9198382938a03ff3db7f47ef6b4780 upstream. Remove the clock configuration from imx_setup_ufcr(). This isn't needed here and will cause garbage output if done. To be be sure that we only touch the bits we want (TXTL and RXTL) we have to mask out all other bits of the UFCR register. Add one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6). Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Shawn Guo <shawn.guo@linaro.org> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Xinyu Chen <xinyu.chen@freescale.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: deleted code in imx_setup_ufcr() refers to sport->clk not sport->clk_per] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7be0670f7b9198382938a03ff3db7f47ef6b4780 upstream.

Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.

To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: deleted code in imx_setup_ufcr() refers to
 sport->clk not sport->clk_per]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tty: serial: imx: console write routing is unsafe on SMP 2012-09-19T14:05:14+00:00 Xinyu Chen xinyu.chen@freescale.com 2012-08-27T07:36:51+00:00 c096552004244868391b29f319ea8889d55abe19 commit 9ec1882df244c4ee1baa692676fef5e8b0f5487d upstream. The console feature's write routing is unsafe on SMP with the startup/shutdown call. There could be several consumers of the console * the kernel printk * the init process using /dev/kmsg to call printk to show log * shell, which open /dev/console and write with sys_write() The shell goes into the normal uart open/write routing, but the other two go into the console operations. The open routing calls imx serial startup, which will write USR1/2 register without any lock and critical with imx_console_write call. Add a spin_lock for startup/shutdown/console_write routing. This patch is a port from Freescale's Android kernel. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com> Tested-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 9ec1882df244c4ee1baa692676fef5e8b0f5487d upstream.

The console feature's write routing is unsafe on SMP with
the startup/shutdown call.

There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()

The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.

Add a spin_lock for startup/shutdown/console_write routing.

This patch is a port from Freescale's Android kernel.

Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pmac_zilog,kdb: Fix console poll hook to return instead of loop 2012-09-12T02:37:34+00:00 Jason Wessel jason.wessel@windriver.com 2012-08-12T12:16:43+00:00 4422e6fe13eff3fc4337dedc76f6830e1a3b4e1a commit 38f8eefccf3a23c4058a570fa2938a4f553cf8e0 upstream. kdb <-> kgdb transitioning does not work properly with this UART driver because the get character routine loops indefinitely as opposed to returning NO_POLL_CHAR per the expectation of the KDB I/O driver API. The symptom is a kernel hang when trying to switch debug modes. Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 38f8eefccf3a23c4058a570fa2938a4f553cf8e0 upstream.

kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.

The symptom is a kernel hang when trying to switch debug modes.

Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pch_uart: Fix parity setting issue 2012-08-09T23:25:19+00:00 Tomoya MORINAGA tomoya.rohm@gmail.com 2012-07-06T08:19:43+00:00 dbf6df1f6b4c2057a0e07b8a0f9c8f041b96f2d0 commit 38bd2a1ac736901d1cf4971c78ef952ba92ef78b upstream. Parity Setting value is reverse. E.G. In case of setting ODD parity, EVEN value is set. This patch inverts "if" condition. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 38bd2a1ac736901d1cf4971c78ef952ba92ef78b upstream.

Parity Setting value is reverse.
E.G. In case of setting ODD parity, EVEN value is set.
This patch inverts "if" condition.

Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pch_uart: Fix rx error interrupt setting issue 2012-08-09T23:25:18+00:00 Tomoya MORINAGA tomoya.rohm@gmail.com 2012-07-06T08:19:42+00:00 0eaadc03ba1b2d870cec52f353adaa9c30b65db7 commit 9539dfb7ac1c84522fe1f79bb7dac2990f3de44a upstream. Rx Error interrupt(E.G. parity error) is not enabled. So, when parity error occurs, error interrupt is not occurred. As a result, the received data is not dropped. This patch adds enable/disable rx error interrupt code. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Backported by Tomoya MORINGA: adjusted context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 9539dfb7ac1c84522fe1f79bb7dac2990f3de44a upstream.

Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.

This patch adds enable/disable rx error interrupt code.

Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Backported by Tomoya MORINGA: adjusted context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pch_uart: Fix missing break for 16 byte fifo 2012-08-09T23:25:17+00:00 Alan Cox alan@linux.intel.com 2012-07-02T17:51:38+00:00 882cd0e86a1640fd70298d13b924c2c9fb8861a7 commit 9bc03743fff0770dc5a5324ba92e67cc377f16ca upstream. Otherwise we fall back to the wrong value. Reported-by: <dcb314@hotmail.com> Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 9bc03743fff0770dc5a5324ba92e67cc377f16ca upstream.

Otherwise we fall back to the wrong value.

Reported-by: <dcb314@hotmail.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tty: Allow uart_register/unregister/register 2012-05-30T23:43:42+00:00 Alan Cox alan@linux.intel.com 2012-05-14T13:51:22+00:00 b89d788669db009d58b2f5e9988caaaf7df9e4ab commit 1e66cded334e6cea596c72f6f650eec351b1e959 upstream. This is legitimate but because we don't clear the drv->state pointer in the unregister code causes a bogus BUG(). Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 1e66cded334e6cea596c72f6f650eec351b1e959 upstream.

This is legitimate but because we don't clear the drv->state pointer in the
unregister code causes a bogus BUG().

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>