linux-toradex.git/drivers/tty/serial, branch v4.9.66

serial: 8250_fintek: Fix finding base_port with activated SuperIO

2017-11-24T07:33:42+00:00

commit fd97e66c5529046e989a0879c3bb58fddb592c71 upstream.

The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().

Tested on iBASE MI802.

Tested-by: Ji-Ze Hong (Peter Hong) 
Signed-off-by: Ji-Ze Hong (Peter Hong) 
Reviewd-by: Alan Cox 
Signed-off-by: Greg Kroah-Hartman

serial: omap: Fix EFR write on RTS deassertion

2017-11-24T07:33:42+00:00

commit 2a71de2f7366fb1aec632116d0549ec56d6a3940 upstream.

Commit 348f9bb31c56 ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.

Fixes: 348f9bb31c56 ("serial: omap: Fix RTS handling")
Cc: Peter Hurley 
Signed-off-by: Lukas Wunner 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix register offsets for the IRDA serial port

2017-11-15T14:53:14+00:00

[ Upstream commit a752ba18af8285e3eeda572f40dddaebff0c3621 ]

Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.

Signed-off-by: Laurent Pinchart 
Reviewed-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

sparc64: Migrate hvcons irq to panicked cpu

2017-10-21T15:21:35+00:00

[ Upstream commit 7dd4fcf5b70694dc961eb6b954673e4fc9730dbd ]

On panic, all other CPUs are stopped except the one which had
hit panic. To keep console alive, we need to migrate hvcons irq
to panicked CPU.

Signed-off-by: Vijay Kumar 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_port: Remove dangerous pr_debug()

2017-10-08T08:26:05+00:00

[ Upstream commit 699a11ba7ec869b006623182881f2f1f5b4aea53 ]

With CONFIG_DYNAMIC_DEBUG if dyndbg enables debug output in
8250_port.c deadlock happens inevitably on UART IRQ handling.

That's the problematic execution path:
---------------------------->8------------------------
UART IRQ:
  serial8250_interrupt() ->
    serial8250_handle_irq(): lock "port->lock" ->
      pr_debug() ->
        serial8250_console_write(): bump in locked "port->lock".

      OR (if above pr_debug() gets removed):
      serial8250_tx_chars() ->
        pr_debug() ->
          serial8250_console_write(): bump in locked "port->lock".
---------------------------->8------------------------

So let's get rid of those not that much useful debug entries.

Discussed problem could be easily reproduced with QEMU for x86_64.
As well as this fix could be mimicked with muting of dynamic debug for
the problematic lines as simple as:
---------------------------->8------------------------
dyndbg="+p; file 8250_port.c line 1756 -p; file 8250_port.c line 1822 -p"
---------------------------->8------------------------

Signed-off-by: Alexey Brodkin 
Cc: Jiri Slaby 
Cc: Peter Hurley 
Cc: Phillip Raffeck 
Cc: Anton Wuerfel 
Cc: "Matwey V. Kornilov" 
Cc: Yegor Yefremov 
Cc: Thor Thayer 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: moxa: Store num_ports in brd

2017-10-08T08:26:05+00:00

[ Upstream commit 9c4b60fe5313c125b1bf68ef04b0010512c27f2d ]

When struct moxa8250_board is allocated, then num_ports should
be initialized in order to use it later in moxa8250_remove.

Signed-off-by: Matwey V. Kornilov 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix late enablement of AUTORTS

2017-06-24T05:11:14+00:00

commit 5f76895e4c712b1b5af450cf344389b8c53ac2c2 upstream.

When changing hardware control flow for a UART with dedicated RTS/CTS
pins, the new AUTORTS state is not immediately reflected in the
hardware, but only when RTS is raised.  However, the serial core does
not call .set_mctrl() after .set_termios(), hence AUTORTS may only
become effective when the port is closed, and reopened later.
Note that this problem does not happen when manually using stty to
change CRTSCTS, as AUTORTS will work fine on next open.

To fix this, call .set_mctrl() from .set_termios() when dedicated
RTS/CTS pins are present, to refresh the AUTORTS or RTS state.
This is similar to what other drivers supporting AUTORTS do (e.g.
omap-serial).

Reported-by: Baumann, Christoph (C.) 
Fixes: 33f50ffc253854cf ("serial: sh-sci: Fix support for hardware-assisted RTS/CTS")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'

2017-06-24T05:11:14+00:00

commit be40597a1bc173bf9dadccdf5388b956f620ae8f upstream.

UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.

Fixes: 3afbd89c9639 ("serial/efm32: add new driver")
Signed-off-by: Christophe JAILLET 
Acked-by: Uwe Kleine-König 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix panic when serial console and DMA are enabled

2017-06-14T13:06:04+00:00

commit 3c9101766b502a0163d1d437fada5801cf616be2 upstream.

This patch fixes an issue that kernel panic happens when DMA is enabled
and we press enter key while the kernel booting on the serial console.

* An interrupt may occur after sci_request_irq().
* DMA transfer area is initialized by setup_timer() in sci_request_dma()
  and used in interrupt.

If an interrupt occurred between sci_request_irq() and setup_timer() in
sci_request_dma(), DMA transfer area has not been initialized yet.
So, this patch changes the order of sci_request_irq() and
sci_request_dma().

Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Takatoshi Akiyama 
[Shimoda changes the commit log]
Signed-off-by: Yoshihiro Shimoda 
Cc: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman

serial: ifx6x60: fix use-after-free on module unload

2017-06-14T13:05:54+00:00

commit 1e948479b3d63e3ac0ecca13cbf4921c7d17c168 upstream.

Make sure to deregister the SPI driver before releasing the tty driver
to avoid use-after-free in the SPI remove callback where the tty
devices are deregistered.

Fixes: 72d4724ea54c ("serial: ifx6x60: Add modem power off function in the platform reboot process")
Cc: Jun Chen 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman