A number of configuration file changes. These are mainly to replace references to ARCH_AT91RM9200 and ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't need to mention every specific AT91 processor explicitly. Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK boards. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
inlined is the patch that adds basic support for USB OHCI controller support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it depends on I2C driver for PNX4008 which I've recetnly posted to LKML and i2c at lm-sensors. Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OHCI updates for AT91 series processors: - Get ready for at91sam926x processors (ARMv5tej not ARMv4t) - Suspend/resume support now behaves properly - In "standby" mode, OHCI can be a source of system wakeup events (remote wakeup, device connect/disconnect, etc) And minor cleanups. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds OHCI glue bits for the USB host interface in the Cirrus ep93xx (arm920t) CPU. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of historic reasons, there are two separate directories with V4L stuff. Most drivers are located at driver/media/video. However, some code for USB Webcams were inserted under drivers/usb/media. This makes difficult for module authors to know were things should be. Also, makes Kconfig menu confusing for normal users. This patch moves all V4L content under drivers/usb/media to drivers/media/video, and fixes Kconfig/Makefile entries. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for OHCI on AT91rm9200 based boards. Possibly of interest here is the way this uses <linux/clk.h> to gate clocks on/off during system pm state transitions. That's typical for non-PCI systems. Some can go further; Mini-A host side connectors enable ID-pin sensing. From: Andrew Victor <andrew@sanpeople.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ALCHEMY: Add EHCI support for AU1200 Updated by removing the OHCI support Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding a Host Mode USB driver for the Freescale 83xx. This driver supports both the Dual-Role (DR) controller and the Multi-Port-Host (MPH) controller present in the Freescale MPC8349. It has been tested with the MPC8349CDS reference system. This driver depends on platform support code for setting up the pins on the device package in a manner appropriate for the board in use. Note that this patch requires selecting the EHCI controller option under the USB Host menu. Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB (OHCI) Host driver for S3C2410/S3C2440 based systems Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!