commit 251b3c8b57481bcecd3f753108e36e7389ce12ac upstream.

Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
   in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.

Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ae3e57ae26cdcc85728bb566f999bcb9a7cc6954 upstream.

Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 85da852df66e5e0d3aba761b0fece7c958ff0685 upstream.

This patch is to support load and unload gadget driver in full OTG mode.

Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use imx6sx instead of imx6sl's platform flags for imx6sx.

Fixes: e14db48dfcf3 ("usb: chipidea: imx: add runtime power management support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

Due to having hardware tx buffers less than 512 bytes in size, streaming
must be enabled on the Zynq for the udc to work at all.  Add platform data
specific to the Zynq udc, which does not set the CI_HDRC_DISABLE_STREAMING
flag.

Based on a patch by the same name from the Xilinx vendor tree.

Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

According to spec, there are functional and protocol stalls.

For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).

For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).

It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.

Cc: <stable@vger.kernel.org> #3.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>

Peter writes:

USB: chipidea updates for v4.3-rc1

The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.

Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.

Felipe writes:

usb: patches for v4.3 merge window

New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.

DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.

Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.

Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.

Signed-off-by: Felipe Balbi <balbi@ti.com>

The user can adjust it through dts or platform data

Signed-off-by: Peter Chen <peter.chen@freescale.com>

With this setting and AHBBRST at SBUSCFG as "Incremental burst of
unspecified length", each non-burst size can be taken as single
transfer. It is benefit for non-burst size transfer.

Signed-off-by: Peter Chen <peter.chen@freescale.com>