linux-toradex.git/drivers/usb/core/hcd.c, branch v3.10.45

Revert "usbcore: set lpm_capable field for LPM capable root hubs"

2014-02-22T20:41:28+00:00

commit 140e3026a57ab7d830dab2f2c57796c222db0ea9 upstream.

Commit 9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.

Unfortunately, that's not the case.  The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).

When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:

Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2

lspci for the affected host:

04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
        Subsystem: 1043:1039
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
Reported-by: Sergey Galanov 
Signed-off-by: Greg Kroah-Hartman

usbcore: set lpm_capable field for LPM capable root hubs

2013-11-20T20:27:48+00:00

commit 9df89d85b407690afa46ddfbccc80bec6869971d upstream.

This patch sets the lpm_capable field for root hubs with LPM capabilities.

Signed-off-by: Xenia Ragiadakou 
Reported-by: Martin MOKREJS 
Suggested-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: remove CONFIG_USB_SUSPEND option

2013-03-28T18:10:22+00:00

This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM).  The net result is code
shrinkage and simplification.

There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it.  The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.

Signed-off-by: Alan Stern 
CC: Peter Chen 
Signed-off-by: Greg Kroah-Hartman

usb: add find_raw_port_number callback to struct hc_driver()

2013-03-25T17:39:17+00:00

xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().

Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.

All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
     (1) root port that doesn't have an entry
     (2) root port with unknown speed
     (3) root port that is listed twice and with different speeds.

So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.

Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp

Merge usb-linus branch into usb-next

2013-02-08T20:03:11+00:00

This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.

Signed-off-by: Greg Kroah-Hartman

USB: add usb_hcd_{start,end}_port_resume

2013-01-25T23:06:01+00:00

This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port.  The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.

Since commit 596d789a211d134dc5f94d1e5957248c204ef850 (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use.  While a root-hub port is being resumed,
the root hub does not appear to be in use.  Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again.  We want to prevent this wasteful effort.

Signed-off-by: Alan Stern 
Tested-by: Ming Lei 
Signed-off-by: Greg Kroah-Hartman

USB: Set usb port's DeviceRemovable according acpi information

2013-01-21T21:22:03+00:00

ACPI provide "_PLD" and "_UPC" aml methods to describe usb port
visibility and connectability. This patch is to add usb_hub_adjust_DeviceRemovable()
to adjust usb hub port's DeviceRemovable according ACPI information and invoke it in
the rh_call_control(). When hub descriptor request is issued at first time,
usb port device isn't created and usb port is not bound with acpi. So first
hub descriptor request is not changed based on ACPI information. After usb
port devices being created, call usb_hub_adjust_DeviceRemovable in the hub_configure()
and then set hub port's DeviceRemovable according ACPI information and this also works
for non-root hub.

Acked-by: Alan Stern 
Signed-off-by: Lan Tianyu 
Signed-off-by: Greg Kroah-Hartman

usb/core: update power budget for SuperSpeed

2013-01-12T00:16:01+00:00

Sarah pointed out that the USB3.0 spec also updates the amount of power
that may be consumed by the device and quoted 9.2.5.1:

|"The amount of current draw for SuperSpeed devices are increased to 150
|mA for low-power devices and 900 mA for high-power"

This patch tries to update all users to use the larger values for
SuperSpeed devices and use the "old" ones for everything else.

While here, two other changes suggested by Alan:
- the comment referering to 7.2.1.1 has been updated to 7.2.1 which is
  the correct source of the action.
- the check for hubs with zero ports has been removed.
- compute bus power by full_load * num_ports on root hubs

Acked-by: Alan Stern 
Acked-by: Sarah Sharp 
Signed-off-by: Sebastian Andrzej Siewior 
Signed-off-by: Greg Kroah-Hartman

Merge 3.7-rc6 into usb-next.

2012-11-17T02:46:21+00:00

This resolves a conflict with these files:
	drivers/usb/early/ehci-dbgp.c
	drivers/usb/host/ehci-ls1x.c
	drivers/usb/host/ohci-xls.c
	drivers/usb/musb/ux500.c

Signed-off-by: Greg Kroah-Hartman

Revert "USB/host: Cleanup unneccessary irq disable code"

2012-11-13T18:52:52+00:00

This reverts commit 73d4066055e0e2830533041f4b91df8e6e5976ff.

Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled.  Thomas pointed out that this patch
is incorrect, and can cause problems.  So revert it to get the
previously working functionality back.

Reported-by: Martin Steigerwald 
Cc: Thomas Gleixner 
Cc: Chuansheng Liu 
Cc: Alan Stern 
Signed-off-by: Greg Kroah-Hartman