linux-toradex.git/drivers/usb/core, branch v4.9.15

USB: Add quirk for WORLDE easykey.25 MIDI keyboard

2017-02-09T07:08:30+00:00

commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa upstream.

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]

Signed-off-by: Lukáš Lalinský 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Move hub_port_disable() to fix warning if PM is disabled

2017-01-12T10:39:18+00:00

commit 3bc02bce908c7250781376052248f5cd60a4e3d4 upstream.

If CONFIG_PM=n:

    drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
    drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here

To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.

Fixes: 37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

USB: fix problems with duplicate endpoint addresses

2017-01-12T10:39:10+00:00

commit 0a8fd1346254974c3a852338508e4a4cddbb35f1 upstream.

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [] panic+0x1cb/0x3a9 kernel/panic.c:179
 [] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [] kobject_add+0x139/0x220 lib/kobject.c:411
 [] device_add+0x353/0x1660 drivers/base/core.c:1088
 [] device_register+0x1d/0x20 drivers/base/core.c:1206
 [] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.

Signed-off-by: Alan Stern 
Reported-by: Andrey Konovalov 
Tested-by: Andrey Konovalov 
Signed-off-by: Greg Kroah-Hartman

usb: core: usbport: Use proper LED API to fix potential crash

2017-01-06T09:40:11+00:00

commit 89778ba335e302a450932ce5b703c1ee6216e949 upstream.

Calling brightness_set manually isn't safe as some LED drivers don't
implement this callback. The best idea is to just use a proper helper
which will fallback to the brightness_set_blocking callback if needed.

This fixes:
[ 1461.761528] Unable to handle kernel NULL pointer dereference at virtual address 00000000
(...)
[ 1462.117049] Backtrace:
[ 1462.119521] [] (usbport_trig_port_store [ledtrig_usbport]) from [] (dev_attr_store+0x20/0x2c)
[ 1462.129826]  r7:dcabc7c0 r6:dee0ff80 r5:00000002 r4:bf228164
[ 1462.135511] [] (dev_attr_store) from [] (sysfs_kf_write+0x48/0x4c)
[ 1462.143459]  r5:00000002 r4:c023f738
[ 1462.147049] [] (sysfs_kf_write) from [] (kernfs_fop_write+0xf8/0x1f8)
[ 1462.155258]  r5:00000002 r4:df4a1000
[ 1462.158850] [] (kernfs_fop_write) from [] (__vfs_write+0x34/0x120)
[ 1462.166800]  r10:00000000 r9:dee0e000 r8:c000fc24 r7:00000002 r6:dee0ff80 r5:c01689c0
[ 1462.174660]  r4:df727a80
[ 1462.177204] [] (__vfs_write) from [] (vfs_write+0xac/0x170)
[ 1462.184543]  r9:dee0e000 r8:c000fc24 r7:dee0ff80 r6:b6f092d0 r5:df727a80 r4:00000002
[ 1462.192319] [] (vfs_write) from [] (SyS_write+0x4c/0xa8)
[ 1462.199396]  r9:dee0e000 r8:c000fc24 r7:00000002 r6:b6f092d0 r5:df727a80 r4:df727a80
[ 1462.207174] [] (SyS_write) from [] (ret_fast_syscall+0x0/0x3c)
[ 1462.214774]  r7:00000004 r6:ffffffff r5:00000000 r4:00000000
[ 1462.220456] Code: bad PC value
[ 1462.223560] ---[ end trace 676638a3a12c7a56 ]---

Reported-by: Ralph Sennhauser 
Signed-off-by: Rafał Miłecki 
Fixes: 0f247626cbb ("usb: core: Introduce a USB port LED trigger")
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices

2017-01-06T09:40:11+00:00

commit 37be66767e3cae4fd16e064d8bb7f9f72bf5c045 upstream.

USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.

For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.

Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.

Cc: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs

2016-10-11T03:16:43+00:00

Pull more vfs updates from Al Viro:
 ">rename2() work from Miklos + current_time() from Deepa"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Replace current_fs_time() with current_time()
  fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
  fs: Replace CURRENT_TIME with current_time() for inode timestamps
  fs: proc: Delete inode time initializations in proc_alloc_inode()
  vfs: Add current_time() api
  vfs: add note about i_op->rename changes to porting
  fs: rename "rename2" i_op to "rename"
  vfs: remove unused i_op->rename
  fs: make remaining filesystems use .rename2
  libfs: support RENAME_NOREPLACE in simple_rename()
  fs: support RENAME_NOREPLACE for local filesystems
  ncpfs: fix unused variable warning

Merge remote-tracking branch 'ovl/rename2' into for-linus

2016-10-11T03:02:51+00:00

fs: Replace CURRENT_TIME with current_time() for inode timestamps

2016-09-28T01:06:21+00:00

CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.

CURRENT_TIME is also not y2038 safe.

This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.

Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.

Signed-off-by: Deepa Dinamani 
Reviewed-by: Arnd Bergmann 
Acked-by: Felipe Balbi 
Acked-by: Steven Whitehouse 
Acked-by: Ryusuke Konishi 
Acked-by: David Sterba 
Signed-off-by: Al Viro

usb: hub: change CLEAR_FEATURE to SET_FEATURE

2016-09-27T10:20:17+00:00

In USB20 specification, describes in chapter 9.4.5: The Remote Wakeup
field can be modified by the SetFeature() and ClearFeature() requests
using the DEVICE_REMOTE_WAKEUP feature selector.

In USB30 specification, also describes in chapter 9.4.5: The Function
Remote Wakeup field can be modified by the SetFeature() requests
using the FUNCTION_SUSPEND feature selector. In chapter 9.4.9 Set
Feature reference, it describes Function Remote Wake Enabled/Disabled
at suspend options by SET_FEATURE.

In USB30 specification only mentioned SetFeature(), so we need use
SET_FEATURE replace CLEAR_FEATURE to disable USB30 function remote
wakeup in suspend options.

Signed-off-by: Yonglong Wu 
Signed-off-by: Greg Kroah-Hartman

usb: core: Introduce a USB port LED trigger

2016-09-27T10:20:17+00:00

This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various home routers that have USB port(s) and a proper LED telling user
a device is connected.

The trigger gets its documentation file but basically it just requires
enabling it and selecting USB ports (e.g. echo 1 > ports/usb1-1).

There was a long discussion on design of this driver. Its current state
is a result of picking them most adjustable solution as others couldn't
handle all cases.

1) It wasn't possible for the driver to register separated trigger for
   each USB port. Some physical USB ports are handled by more than one
   controller and so by more than one USB port. E.g. USB 2.0 physical
   port may be handled by OHCI's port and EHCI's port.
   It's also not possible to assign more than 1 trigger to a single LED
   and implementing such feature would be tricky due to syncing triggers
   and sysfs conflicts with old triggers.

2) Another idea was to register trigger per USB hub. This wouldn't allow
   handling devices with multiple USB LEDs and controllers (hubs)
   controlling more than 1 physical port. It's common for hubs to have
   few ports and each may have its own LED.

This final trigger is highly flexible. It allows selecting any USB ports
for any LED. It was also modified (comparing to the initial version) to
allow choosing ports rather than having user /guess/ proper names. It
was successfully tested on SmartRG SR400ac which has 3 USB LEDs,
2 physical ports and 3 controllers.

It was noted USB subsystem already has usb-gadget and usb-host triggers
but they are pretty trivial ones. They indicate activity only and can't
have ports specified.

In future it may be good idea to consider adding activity support to
usbport as well. This should allow switching to this more generic driver
and maybe marking old ones as obsolete.
This can be implemented with another sysfs file for setting mode. The
default mode wouldn't change so there won't be ABI breakage and so such
feature can be safely implemented later.

There was also an idea of supporting other devices (PCI, SDIO, etc.) but
as this driver already contains some USB specific code (and will get
more) these should be probably separated drivers (triggers).

Signed-off-by: Rafał Miłecki 
Signed-off-by: Greg Kroah-Hartman