linux-toradex.git/drivers/usb/dwc2, branch v4.9.87

usb: dwc2: gadget: Fix GUSBCFG.USBTRDTIM value

2017-07-05T12:40:26+00:00

[ Upstream commit ca02954ada711b08e5b0d84590a631fd63ed39f9 ]

USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.

Signed-off-by: Amelie Delaunay 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: host: use msleep() for long delay

2017-05-14T12:00:18+00:00

commit d3fe81d2ccc41b355e494413115c0c7c18426fa1 upstream.

ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.

Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63e0c2 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: Nicholas Mc Guire 
Signed-off-by: John Youn 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"

2016-10-18T11:21:40+00:00

This reverts commit aa381a7259c3 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").

The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.

Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.

Signed-off-by: John Youn 
Cc: Robert Baldyga 
Cc: Stefan Wahren 
Signed-off-by: Felipe Balbi

Revert "usb: dwc2: gadget: change variable name to more meaningful"

2016-10-18T11:21:37+00:00

This reverts commit ba48eab8866c ("usb: dwc2: gadget: change variable
name to more meaningful").

This is needed to cleanly revert commit aa381a7259c3 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization") which may cause
regressions on some platforms.

Signed-off-by: John Youn 
Cc: Robert Baldyga 
Cc: Stefan Wahren 
Signed-off-by: Felipe Balbi

usb: dwc2: Add msleep for host-only

2016-10-17T09:30:29+00:00

Although a host-only controller should not have any associated delay,
some rockchip SOC platforms will not show the correct host-values of
registers until after a delay.

So add a 50 ms sleep when in host-only mode.

Signed-off-by: John Youn 
Signed-off-by: Heiko Stuebner 
Signed-off-by: Felipe Balbi

Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2016-10-08T04:34:49+00:00

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

   - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
     automotive SoC similar to the ⅹ8a7795 chip we already support, but
     the dts changes rely on a clock driver change that has been merged
     for v4.9 through the clk tree.

   - The Amlogic meson-gxbb (S905) platform gains support for a few
     drivers merged through our tree, in particular the network and usb
     driver changes are required and included here, and also the clk
     tree changes.

   - The Allwinner platforms have seen a large-scale change to their clk
     drivers and the dts file updates must come after that. This
     includes the newly added Nextthing GR8 platform, which is derived
     from sun5i/A13.

   - Some integrator (arm32) changes rely on clk driver changes.

   - A single patch for lpc32xx has no such dependency but wasn't added
     until just before the merge window"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  ARM: dts: lpc32xx: add device node for IRAM on-chip memory
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ...

Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

2016-09-14T18:37:50+00:00

Felipe writes:

usb: patches for v4.9 merge window

This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).

As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.

The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.

Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.

Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.

usb: dwc2: add support for Meson8b and GXBB SoCs

2016-09-14T18:18:52+00:00

Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.

Signed-off-by: Jerome Brunet 
Signed-off-by: Martin Blumenstingl 
Acked-by: John Youn 
Signed-off-by: Kevin Hilman

usb: dwc2: Properly account for the force mode delays

2016-09-08T11:02:54+00:00

When a force mode bit is set and the IDDIG debounce filter is enabled,
there is a delay for the forced mode to take effect. This delay is due
to the IDDIG debounce filter and is variable depending on the platform's
PHY clock speed. To account for this delay we can poll for the expected
mode.

On a clear force mode, since we don't know what mode to poll for, delay
for a fixed 100 ms. This is the maximum delay based on the slowest PHY
clock speed.

Tested-by: Stefan Wahren 
Signed-off-by: John Youn 
Signed-off-by: Felipe Balbi

usb: dwc2: Add delay to core soft reset

2016-09-08T11:02:52+00:00

Add a delay to the core soft reset function to account for the IDDIG
debounce filter.

If the current mode is host, either due to the force mode bit being
set (which persists after core reset) or the connector id pin, a core
soft reset will temporarily reset the mode to device and a delay from
the IDDIG debounce filter will occur before going back to host mode.

Tested-by: Stefan Wahren 
Signed-off-by: John Youn 
Signed-off-by: Felipe Balbi