linux-toradex.git/drivers/usb/dwc2, branch v4.9.97

usb: dwc2: Improve gadget state disconnection handling

2018-04-08T10:12:50+00:00

commit d2471d4a24dfbff5e463d382e2c6fec7d7e25a09 upstream.

In the earlier commit dad3f793f20f ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.

(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)

The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.

But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.

Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.

Cc: Wei Xu 
Cc: Guodong Xu 
Cc: Amit Pundir 
Cc: YongQin Liu 
Cc: John Youn 
Cc: Minas Harutyunyan 
Cc: Douglas Anderson 
Cc: Chen Yu 
Cc: Felipe Balbi 
Cc: Greg Kroah-Hartman 
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan 
Tested-by: Minas Harutyunyan 
Signed-off-by: John Stultz 
Signed-off-by: Felipe Balbi 
Cc: Ben Hutchings 
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Make sure we disconnect the gadget state

2018-03-22T08:17:50+00:00

[ Upstream commit dad3f793f20fbb5c0c342f0f5a0bdf69a4d76089 ]

I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.

Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.

So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.

With it, the gadget interface initializes properly on every
plug in.

Cc: Wei Xu 
Cc: Guodong Xu 
Cc: Amit Pundir 
Cc: Rob Herring 
Cc: John Youn 
Cc: Douglas Anderson 
Cc: Chen Yu 
Cc: Felipe Balbi 
Cc: Greg Kroah-Hartman 
Cc: linux-usb@vger.kernel.org
Acked-by: John Youn 
Signed-off-by: John Stultz 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: gadget: Fix GUSBCFG.USBTRDTIM value

2017-07-05T12:40:26+00:00

[ Upstream commit ca02954ada711b08e5b0d84590a631fd63ed39f9 ]

USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.

Signed-off-by: Amelie Delaunay 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: host: use msleep() for long delay

2017-05-14T12:00:18+00:00

commit d3fe81d2ccc41b355e494413115c0c7c18426fa1 upstream.

ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.

Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63e0c2 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: Nicholas Mc Guire 
Signed-off-by: John Youn 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"

2016-10-18T11:21:40+00:00

This reverts commit aa381a7259c3 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").

The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.

Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.

Signed-off-by: John Youn 
Cc: Robert Baldyga 
Cc: Stefan Wahren 
Signed-off-by: Felipe Balbi

Revert "usb: dwc2: gadget: change variable name to more meaningful"

2016-10-18T11:21:37+00:00

This reverts commit ba48eab8866c ("usb: dwc2: gadget: change variable
name to more meaningful").

This is needed to cleanly revert commit aa381a7259c3 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization") which may cause
regressions on some platforms.

Signed-off-by: John Youn 
Cc: Robert Baldyga 
Cc: Stefan Wahren 
Signed-off-by: Felipe Balbi

usb: dwc2: Add msleep for host-only

2016-10-17T09:30:29+00:00

Although a host-only controller should not have any associated delay,
some rockchip SOC platforms will not show the correct host-values of
registers until after a delay.

So add a 50 ms sleep when in host-only mode.

Signed-off-by: John Youn 
Signed-off-by: Heiko Stuebner 
Signed-off-by: Felipe Balbi

Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2016-10-08T04:34:49+00:00

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

   - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
     automotive SoC similar to the ⅹ8a7795 chip we already support, but
     the dts changes rely on a clock driver change that has been merged
     for v4.9 through the clk tree.

   - The Amlogic meson-gxbb (S905) platform gains support for a few
     drivers merged through our tree, in particular the network and usb
     driver changes are required and included here, and also the clk
     tree changes.

   - The Allwinner platforms have seen a large-scale change to their clk
     drivers and the dts file updates must come after that. This
     includes the newly added Nextthing GR8 platform, which is derived
     from sun5i/A13.

   - Some integrator (arm32) changes rely on clk driver changes.

   - A single patch for lpc32xx has no such dependency but wasn't added
     until just before the merge window"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  ARM: dts: lpc32xx: add device node for IRAM on-chip memory
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ...

Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

2016-09-14T18:37:50+00:00

Felipe writes:

usb: patches for v4.9 merge window

This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).

As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.

The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.

Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.

Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.

usb: dwc2: add support for Meson8b and GXBB SoCs

2016-09-14T18:18:52+00:00

Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.

Signed-off-by: Jerome Brunet 
Signed-off-by: Martin Blumenstingl 
Acked-by: John Youn 
Signed-off-by: Kevin Hilman