linux-toradex.git/drivers/usb/gadget, branch v4.9.32 Linux kernel for Apalis and Colibri modules usb: gadget: f_mass_storage: Serialize wake and sleep execution 2017-06-14T13:05:58+00:00 Thinh Nguyen Thinh.Nguyen@synopsys.com 2017-05-12T00:26:48+00:00 405ac24a0aecc6c60134900dcb5fa46322b9a9a4 commit dc9217b69dd6089dcfeb86ed4b3c671504326087 upstream. f_mass_storage has a memorry barrier issue with the sleep and wake functions that can cause a deadlock. This results in intermittent hangs during MSC file transfer. The host will reset the device after receiving no response to resume the transfer. This issue is seen when dwc3 is processing 2 transfer-in-progress events at the same time, invoking completion handlers for CSW and CBW. Also this issue occurs depending on the system timing and latency. To increase the chance to hit this issue, you can force dwc3 driver to wait and process those 2 events at once by adding a small delay (~100us) in dwc3_check_event_buf() whenever the request is for CSW and read the event count again. Avoid debugging with printk and ftrace as extra delays and memory barrier will mask this issue. Scenario which can lead to failure: ----------------------------------- 1) The main thread sleeps and waits for the next command in get_next_command(). 2) bulk_in_complete() wakes up main thread for CSW. 3) bulk_out_complete() tries to wake up the running main thread for CBW. 4) thread_wakeup_needed is not loaded with correct value in sleep_thread(). 5) Main thread goes to sleep again. The pattern is shown below. Note the 2 critical variables. * common->thread_wakeup_needed * bh->state CPU 0 (sleep_thread) CPU 1 (wakeup_thread) ============================== =============================== bh->state = BH_STATE_FULL; smp_wmb(); thread_wakeup_needed = 0; thread_wakeup_needed = 1; smp_rmb(); if (bh->state != BH_STATE_FULL) sleep again ... As pointed out by Alan Stern, this is an R-pattern issue. The issue can be seen when there are two wakeups in quick succession. The thread_wakeup_needed can be overwritten in sleep_thread, and the read of the bh->state maybe reordered before the write to thread_wakeup_needed. This patch applies full memory barrier smp_mb() in both sleep_thread() and wakeup_thread() to ensure the order which the thread_wakeup_needed and bh->state are written and loaded. However, a better solution in the future would be to use wait_queue method that takes care of managing memory barrier between waker and waiter. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit dc9217b69dd6089dcfeb86ed4b3c671504326087 upstream.

f_mass_storage has a memorry barrier issue with the sleep and wake
functions that can cause a deadlock. This results in intermittent hangs
during MSC file transfer. The host will reset the device after receiving
no response to resume the transfer. This issue is seen when dwc3 is
processing 2 transfer-in-progress events at the same time, invoking
completion handlers for CSW and CBW. Also this issue occurs depending on
the system timing and latency.

To increase the chance to hit this issue, you can force dwc3 driver to
wait and process those 2 events at once by adding a small delay (~100us)
in dwc3_check_event_buf() whenever the request is for CSW and read the
event count again. Avoid debugging with printk and ftrace as extra
delays and memory barrier will mask this issue.

Scenario which can lead to failure:
-----------------------------------
1) The main thread sleeps and waits for the next command in
   get_next_command().
2) bulk_in_complete() wakes up main thread for CSW.
3) bulk_out_complete() tries to wake up the running main thread for CBW.
4) thread_wakeup_needed is not loaded with correct value in
   sleep_thread().
5) Main thread goes to sleep again.

The pattern is shown below. Note the 2 critical variables.
 * common->thread_wakeup_needed
 * bh->state

	CPU 0 (sleep_thread)		CPU 1 (wakeup_thread)
	==============================  ===============================

					bh->state = BH_STATE_FULL;
					smp_wmb();
	thread_wakeup_needed = 0;	thread_wakeup_needed = 1;
	smp_rmb();
	if (bh->state != BH_STATE_FULL)
		sleep again ...

As pointed out by Alan Stern, this is an R-pattern issue. The issue can
be seen when there are two wakeups in quick succession. The
thread_wakeup_needed can be overwritten in sleep_thread, and the read of
the bh->state maybe reordered before the write to thread_wakeup_needed.

This patch applies full memory barrier smp_mb() in both sleep_thread()
and wakeup_thread() to ensure the order which the thread_wakeup_needed
and bh->state are written and loaded.

However, a better solution in the future would be to use wait_queue
method that takes care of managing memory barrier between waker and
waiter.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: legacy gadgets are optional 2017-05-20T12:28:35+00:00 Romain Izard romain.izard.pro@gmail.com 2017-03-10T13:11:41+00:00 5c51e4b65fca4648a57719ea6b0173261fe523ba commit 6e253d0fbc665b36192b8ed3cecdbb65b413a1eb upstream. With commit bc49d1d17dcf ("usb: gadget: don't couple configfs to legacy gadgets"),it is possible to build a modular kernel with both built-in configfs support and modular legacy gadget drivers. But when building a kernel without modules, it is also necessary to be able to build with configfs but without any legacy gadget driver. This was a possible configuration when the USB_CONFIGFS was a part of the choice options, but not anymore. Mark the choice for legacy gadget drivers as optional restores this. Fixes: bc49d1d17dcf ("usb: gadget: don't couple configfs to legacy gadgets") Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 6e253d0fbc665b36192b8ed3cecdbb65b413a1eb upstream.

With commit bc49d1d17dcf ("usb: gadget: don't couple configfs to legacy
gadgets"),it is possible to build a modular kernel with both built-in
configfs support and modular legacy gadget drivers.

But when building a kernel without modules, it is also necessary to be
able to build with configfs but without any legacy gadget driver. This
was a possible configuration when the USB_CONFIGFS was a part of the
choice options, but not anymore.

Mark the choice for legacy gadget drivers as optional restores this.

Fixes: bc49d1d17dcf ("usb: gadget: don't couple configfs to legacy gadgets")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval 2017-03-30T07:41:23+00:00 Roger Quadros rogerq@ti.com 2017-03-08T14:05:43+00:00 d8ec35ad8b36eba708af614b54eda471ba125eed commit 09424c50b7dff40cb30011c09114404a4656e023 upstream. The streaming_maxburst module parameter is 0 offset (0..15) so we must add 1 while using it for wBytesPerInterval calculation for the SuperSpeed companion descriptor. Without this host uvcvideo driver will always see the wrong wBytesPerInterval for SuperSpeed uvc gadget and may not find a suitable video interface endpoint. e.g. for streaming_maxburst = 0 case it will always fail as wBytePerInterval was evaluating to 0. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 09424c50b7dff40cb30011c09114404a4656e023 upstream.

The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.

Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACM gadget: fix endianness in notifications 2017-03-30T07:41:23+00:00 Oliver Neukum oneukum@suse.com 2017-03-14T11:09:56+00:00 ff8d97a822c65e8ae6ceaa67369c0d56f6797c9b commit cdd7928df0d2efaa3270d711963773a08a4cc8ab upstream. The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: 家瑋 <momo1208@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit cdd7928df0d2efaa3270d711963773a08a4cc8ab upstream.

The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: udc: atmel: remove memory leak 2017-03-22T11:43:39+00:00 Alexandre Belloni alexandre.belloni@free-electrons.com 2017-03-17T00:48:33+00:00 ce7aeffe7596343fce49307f374444b199b950a1 [ Upstream commit 32856eea7bf75dfb99b955ada6e147f553a11366 ] Commit bbe097f092b0 ("usb: gadget: udc: atmel: fix endpoint name") introduced a memory leak when unbinding the driver. The endpoint names would not be freed. Solve that by including the name as a string in struct usba_ep so it is freed when the endpoint is. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 32856eea7bf75dfb99b955ada6e147f553a11366 ]

Commit bbe097f092b0 ("usb: gadget: udc: atmel: fix endpoint name")
introduced a memory leak when unbinding the driver. The endpoint names
would not be freed. Solve that by including the name as a string in struct
usba_ep so it is freed when the endpoint is.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert "usb: gadget: uvc: Add missing call for additional setup data" 2017-03-18T11:14:32+00:00 Roger Quadros rogerq@ti.com 2017-03-02T08:44:58+00:00 03123df08e6b77c0491af64e46054dbef5a1cea4 commit eb38d913c27f32f4df173791051fecf6aca34173 upstream. This reverts commit 4fbac5206afd01b717d4bdc58793d471f3391b4b. This commit breaks g_webcam when used with uvc-gadget [1]. The user space application (e.g. uvc-gadget) is responsible for sending response to UVC class specific requests on control endpoint in uvc_send_response() in uvc_v4l2.c. The bad commit was causing a duplicate response to be sent with incorrect response data thus causing UVC probe to fail at the host and broken control transfer endpoint at the gadget. [1] - git://git.ideasonboard.org/uvc-gadget.git Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit eb38d913c27f32f4df173791051fecf6aca34173 upstream.

This reverts commit 4fbac5206afd01b717d4bdc58793d471f3391b4b.

This commit breaks g_webcam when used with uvc-gadget [1].

The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.

The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.

[1] - git://git.ideasonboard.org/uvc-gadget.git

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: function: f_fs: pass companion descriptor along 2017-03-18T11:14:31+00:00 Felipe Balbi felipe.balbi@linux.intel.com 2017-01-31T12:54:45+00:00 5ce2e4ce4a8a02d1ca9ed0d4aeac7a24cd3a59b9 commit 2bfa0719ac2a9b2f3c91345873d3cdebd0296ba9 upstream. If we're dealing with SuperSpeed endpoints, we need to make sure to pass along the companion descriptor and initialize fields needed by the Gadget API. Eventually, f_fs.c should be converted to use config_ep_by_speed() like all other functions, though. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2bfa0719ac2a9b2f3c91345873d3cdebd0296ba9 upstream.

If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: dummy_hcd: clear usb_gadget region before registration 2017-03-18T11:14:31+00:00 Peter Chen peter.chen@nxp.com 2017-02-28T06:25:45+00:00 de90394b0c6b9cf6e84c8a9ecfb9673e31b88a19 commit 5bbc852676ae08e818241cf66a3ffe4be44225c4 upstream. When the user does device unbind and rebind test, the kernel will show below dump due to usb_gadget memory region is dirty after unbind. Clear usb_gadget region for every new probe. root@imx6qdlsolo:/sys/bus/platform/drivers/dummy_udc# echo dummy_udc.0 > bind [ 102.523312] kobject (eddd78b0): tried to init an initialized object, something is seriously wrong. [ 102.532447] CPU: 0 PID: 734 Comm: sh Not tainted 4.10.0-rc7-00872-g1b2b8e9 #1298 [ 102.539866] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 102.545717] Backtrace: [ 102.548225] [<c010d090>] (dump_backtrace) from [<c010d338>] (show_stack+0x18/0x1c) [ 102.555822] r7:ede34000 r6:60010013 r5:00000000 r4:c0f29418 [ 102.561512] [<c010d320>] (show_stack) from [<c040c2a4>] (dump_stack+0xb4/0xe8) [ 102.568764] [<c040c1f0>] (dump_stack) from [<c040e6d4>] (kobject_init+0x80/0x9c) [ 102.576187] r10:0000001f r9:eddd7000 r8:eeaf8c10 r7:eddd78a8 r6:c177891c r5:c0f3b060 [ 102.584036] r4:eddd78b0 r3:00000000 [ 102.587641] [<c040e654>] (kobject_init) from [<c05359a4>] (device_initialize+0x28/0xf8) [ 102.595665] r5:eebc4800 r4:eddd78a8 [ 102.599268] [<c053597c>] (device_initialize) from [<c05382ac>] (device_register+0x14/0x20) [ 102.607556] r7:eddd78a8 r6:00000000 r5:eebc4800 r4:eddd78a8 [ 102.613256] [<c0538298>] (device_register) from [<c0668ef4>] (usb_add_gadget_udc_release+0x8c/0x1ec) [ 102.622410] r5:eebc4800 r4:eddd7860 [ 102.626015] [<c0668e68>] (usb_add_gadget_udc_release) from [<c0669068>] (usb_add_gadget_udc+0x14/0x18) [ 102.635351] r10:0000001f r9:eddd7000 r8:eddd788c r7:bf003770 r6:eddd77f8 r5:eddd7818 [ 102.643198] r4:eddd785c r3:eddd7b24 [ 102.646834] [<c0669054>] (usb_add_gadget_udc) from [<bf003428>] (dummy_udc_probe+0x170/0x1c4 [dummy_hcd]) [ 102.656458] [<bf0032b8>] (dummy_udc_probe [dummy_hcd]) from [<c053d114>] (platform_drv_probe+0x54/0xb8) [ 102.665881] r10:00000008 r9:c1778960 r8:bf004128 r7:fffffdfb r6:bf004128 r5:eeaf8c10 [ 102.673727] r4:eeaf8c10 [ 102.676293] [<c053d0c0>] (platform_drv_probe) from [<c053b160>] (driver_probe_device+0x264/0x474) [ 102.685186] r7:00000000 r6:00000000 r5:c1778960 r4:eeaf8c10 [ 102.690876] [<c053aefc>] (driver_probe_device) from [<c05397c4>] (bind_store+0xb8/0x14c) [ 102.698994] r10:eeb3bb4c r9:ede34000 r8:0000000c r7:eeaf8c44 r6:bf004128 r5:c0f3b668 [ 102.706840] r4:eeaf8c10 [ 102.709402] [<c053970c>] (bind_store) from [<c0538ca8>] (drv_attr_store+0x28/0x34) [ 102.716998] r9:ede34000 r8:00000000 r7:ee3863c0 r6:ee3863c0 r5:c0538c80 r4:c053970c [ 102.724776] [<c0538c80>] (drv_attr_store) from [<c029c930>] (sysfs_kf_write+0x50/0x54) [ 102.732711] r5:c0538c80 r4:0000000c [ 102.736313] [<c029c8e0>] (sysfs_kf_write) from [<c029be84>] (kernfs_fop_write+0x100/0x214) [ 102.744599] r7:ee3863c0 r6:eeb3bb40 r5:00000000 r4:00000000 [ 102.750287] [<c029bd84>] (kernfs_fop_write) from [<c0222dd8>] (__vfs_write+0x34/0x120) [ 102.758231] r10:00000000 r9:ede34000 r8:c0108bc4 r7:0000000c r6:ede35f80 r5:c029bd84 [ 102.766077] r4:ee223780 [ 102.768638] [<c0222da4>] (__vfs_write) from [<c0224678>] (vfs_write+0xa8/0x170) [ 102.775974] r9:ede34000 r8:c0108bc4 r7:ede35f80 r6:01861cb0 r5:ee223780 r4:0000000c [ 102.783743] [<c02245d0>] (vfs_write) from [<c0225498>] (SyS_write+0x4c/0xa8) [ 102.790818] r9:ede34000 r8:c0108bc4 r7:0000000c r6:01861cb0 r5:ee223780 r4:ee223780 [ 102.798595] [<c022544c>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c) [ 102.806188] r7:00000004 r6:b6e83d58 r5:01861cb0 r4:0000000c Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@nxp.com> Tested-by: Xiaolong Ye <xiaolong.ye@intel.com> Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5bbc852676ae08e818241cf66a3ffe4be44225c4 upstream.

When the user does device unbind and rebind test, the kernel will
show below dump due to usb_gadget memory region is dirty after unbind.
Clear usb_gadget region for every new probe.

root@imx6qdlsolo:/sys/bus/platform/drivers/dummy_udc# echo dummy_udc.0 > bind
[  102.523312] kobject (eddd78b0): tried to init an initialized object, something is seriously wrong.
[  102.532447] CPU: 0 PID: 734 Comm: sh Not tainted 4.10.0-rc7-00872-g1b2b8e9 #1298
[  102.539866] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[  102.545717] Backtrace:
[  102.548225] [<c010d090>] (dump_backtrace) from [<c010d338>] (show_stack+0x18/0x1c)
[  102.555822]  r7:ede34000 r6:60010013 r5:00000000 r4:c0f29418
[  102.561512] [<c010d320>] (show_stack) from [<c040c2a4>] (dump_stack+0xb4/0xe8)
[  102.568764] [<c040c1f0>] (dump_stack) from [<c040e6d4>] (kobject_init+0x80/0x9c)
[  102.576187]  r10:0000001f r9:eddd7000 r8:eeaf8c10 r7:eddd78a8 r6:c177891c r5:c0f3b060
[  102.584036]  r4:eddd78b0 r3:00000000
[  102.587641] [<c040e654>] (kobject_init) from [<c05359a4>] (device_initialize+0x28/0xf8)
[  102.595665]  r5:eebc4800 r4:eddd78a8
[  102.599268] [<c053597c>] (device_initialize) from [<c05382ac>] (device_register+0x14/0x20)
[  102.607556]  r7:eddd78a8 r6:00000000 r5:eebc4800 r4:eddd78a8
[  102.613256] [<c0538298>] (device_register) from [<c0668ef4>] (usb_add_gadget_udc_release+0x8c/0x1ec)
[  102.622410]  r5:eebc4800 r4:eddd7860
[  102.626015] [<c0668e68>] (usb_add_gadget_udc_release) from [<c0669068>] (usb_add_gadget_udc+0x14/0x18)
[  102.635351]  r10:0000001f r9:eddd7000 r8:eddd788c r7:bf003770 r6:eddd77f8 r5:eddd7818
[  102.643198]  r4:eddd785c r3:eddd7b24
[  102.646834] [<c0669054>] (usb_add_gadget_udc) from [<bf003428>] (dummy_udc_probe+0x170/0x1c4 [dummy_hcd])
[  102.656458] [<bf0032b8>] (dummy_udc_probe [dummy_hcd]) from [<c053d114>] (platform_drv_probe+0x54/0xb8)
[  102.665881]  r10:00000008 r9:c1778960 r8:bf004128 r7:fffffdfb r6:bf004128 r5:eeaf8c10
[  102.673727]  r4:eeaf8c10
[  102.676293] [<c053d0c0>] (platform_drv_probe) from [<c053b160>] (driver_probe_device+0x264/0x474)
[  102.685186]  r7:00000000 r6:00000000 r5:c1778960 r4:eeaf8c10
[  102.690876] [<c053aefc>] (driver_probe_device) from [<c05397c4>] (bind_store+0xb8/0x14c)
[  102.698994]  r10:eeb3bb4c r9:ede34000 r8:0000000c r7:eeaf8c44 r6:bf004128 r5:c0f3b668
[  102.706840]  r4:eeaf8c10
[  102.709402] [<c053970c>] (bind_store) from [<c0538ca8>] (drv_attr_store+0x28/0x34)
[  102.716998]  r9:ede34000 r8:00000000 r7:ee3863c0 r6:ee3863c0 r5:c0538c80 r4:c053970c
[  102.724776] [<c0538c80>] (drv_attr_store) from [<c029c930>] (sysfs_kf_write+0x50/0x54)
[  102.732711]  r5:c0538c80 r4:0000000c
[  102.736313] [<c029c8e0>] (sysfs_kf_write) from [<c029be84>] (kernfs_fop_write+0x100/0x214)
[  102.744599]  r7:ee3863c0 r6:eeb3bb40 r5:00000000 r4:00000000
[  102.750287] [<c029bd84>] (kernfs_fop_write) from [<c0222dd8>] (__vfs_write+0x34/0x120)
[  102.758231]  r10:00000000 r9:ede34000 r8:c0108bc4 r7:0000000c r6:ede35f80 r5:c029bd84
[  102.766077]  r4:ee223780
[  102.768638] [<c0222da4>] (__vfs_write) from [<c0224678>] (vfs_write+0xa8/0x170)
[  102.775974]  r9:ede34000 r8:c0108bc4 r7:ede35f80 r6:01861cb0 r5:ee223780 r4:0000000c
[  102.783743] [<c02245d0>] (vfs_write) from [<c0225498>] (SyS_write+0x4c/0xa8)
[  102.790818]  r9:ede34000 r8:c0108bc4 r7:0000000c r6:01861cb0 r5:ee223780 r4:ee223780
[  102.798595] [<c022544c>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
[  102.806188]  r7:00000004 r6:b6e83d58 r5:01861cb0 r4:0000000c

Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: f_hid: Use spinlock instead of mutex 2017-03-12T05:41:49+00:00 Krzysztof Opasiak kopasiak90@gmail.com 2017-01-19T17:55:29+00:00 6d0511ed15db30965f8a3be8f0733bb6efd2b95e commit 33e4c1a9987a1fc3b42c3b534100b5b006d55c61 upstream. As IN request has to be allocated in set_alt() and released in disable() we cannot use mutex to protect it as we cannot sleep in those funcitons. Let's replace this mutex with a spinlock. Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 33e4c1a9987a1fc3b42c3b534100b5b006d55c61 upstream.

As IN request has to be allocated in set_alt() and released in
disable() we cannot use mutex to protect it as we cannot sleep
in those funcitons. Let's replace this mutex with a spinlock.

Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: f_hid: fix: Prevent accessing released memory 2017-03-12T05:41:49+00:00 Krzysztof Opasiak kopasiak90@gmail.com 2017-01-19T17:55:28+00:00 d3acd94c0f79387b0d1855bdd4690f1596eb3f25 commit aa65d11aa008f4de58a9cee7e121666d9d68505e upstream. When we unlock our spinlock to copy data to user we may get disabled by USB host and free the whole list of completed out requests including the one from which we are copying the data to user memory. To prevent from this let's remove our working element from the list and place it back only if there is sth left when we finish with it. Fixes: 99c515005857 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT") Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit aa65d11aa008f4de58a9cee7e121666d9d68505e upstream.

When we unlock our spinlock to copy data to user we may get
disabled by USB host and free the whole list of completed out
requests including the one from which we are copying the data
to user memory.

To prevent from this let's remove our working element from
the list and place it back only if there is sth left when we
finish with it.

Fixes: 99c515005857 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT")
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>