Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the drivers that no longer need it, it is removed.
It is removed from the Makefile. Drivers not fully converted
to dynamic debug have it shifted down into the individual
drivers.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT.  This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.

Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec.  However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over.  For the time being, we leave the calculations as they are.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes.  This will drastically speed up the bandwidth
computations.

In addition, it eliminates a theoretical bug.  An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule.  The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.

As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use.  Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.

A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64.  In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).

Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64).  This adds only a
small amount of overhead: 3 bytes for each endpoint.

The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers.  It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.

Initially we merely create the new structure and move some existing
fields into it.  Later patches will add more fields and utilize these
structures in improved scheduling algorithms.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These aren't necessary after switch and if blocks.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.

Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.

Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1664) converts ehci-hcd's async_unlink, async_iaa, and
intr_unlink from singly-linked lists to standard doubly-linked
list_heads.  Originally it didn't seem necessary to use list_heads,
because items are always added to and removed from these lists in FIFO
order.  But now with more list processing going on, it's easier to use
the standard routines than continue with a roll-your-own approach.

I don't know if the code ends up being notably shorter, but the
patterns will be more familiar to any kernel hacker.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1622) removes the USB-2.1 Link Power Management code
from the ehci-hcd driver.  This code was never integrated with
usbcore, it is full of bugs, and it was not getting used by anybody.

However, the debugging code for dumping the LPM-related fields in the
EHCI registers is left in place.  In theory it might be useful to see
these values, even though we don't use them.

This essentially amounts to a partial revert of commit
aa4d8342988d0c1a79ff19b2ede1e81dfbb16ea5 (USB: EHCI: EHCI 1.1
addendum: preparation) and an almost full revert of commit
48f24970144479c29b8cee6d2e1dbedf6dcf9cfb (USB: EHCI: EHCI 1.1
addendum: Basic LPM feature support) plus its follow-ons.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>