commit dc75ce9d929aabeb0843a6b1a4ab320e58ba1597 upstream.

This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub.  A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.

Right now the driver tests whether the root hub is running, and that
is not the correct test.  In particular, if the controller has died
then the root hub should not be restarted.  In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.

In the end, the test needs to be changed.  Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended.  This will yield the correct
behavior in all cases.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>

commit 2fbe2bf1fd37f9d99950bd8d8093623cf22cf08b upstream.

This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.

Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 68aa95d5d4de31c9348c1628ffa85c805305ebc5 upstream.

This patch (as1489) works around a hardware bug in MosChip EHCI
controllers.  Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter).  If the register is read at just the wrong time, the value
obtained is too low by 8.

When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0.  This gives the hardware a chance to
finish updating the register, yielding the correct value.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 2093c6b49c8f1dc581d8953aca71297d4cace55e upstream.

This allow to clean duplicated code in most of SOC driver.

Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit 004c19682884d4f40000ce1ded53f4a1d0b18206 upstream.

This patch (as1477) fixes a problem affecting a few types of EHCI
controller.  Contrary to what one might expect, these controllers
automatically stop their internal frame counter when no ports are
enabled.  Since ehci-hcd currently relies on the frame counter for
determining when it should unlink QHs from the async schedule, those
controllers run into trouble: The frame counter stops and the QHs
never get unlinked.

Some systems have also experienced other problems traced back to
commit b963801164618e25fbdc0cd452ce49c3628b46c8 (USB: ehci-hcd unlink
speedups), which made the original switch from using the system clock
to using the frame counter.  It never became clear what the reason was
for these problems, but evidently it is related to use of the frame
counter.

To fix all these problems, this patch more or less reverts that commit
and goes back to using the system clock.  But this can't be done
cleanly because other changes have since been made to the scan_async()
subroutine.  One of these changes involved the tricky logic that tries
to avoid rescanning QHs that have already been seen when the scanning
loop is restarted, which happens whenever an URB is given back.
Switching back to clock-based unlinks would make this logic even more
complicated.

Therefore the new code doesn't rescan the entire async list whenever a
giveback occurs.  Instead it rescans only the current QH and continues
on from there.  This requires the use of a separate pointer to keep
track of the next QH to scan, since the current QH may be unlinked
while the scanning is in progress.  That new pointer must be global,
so that it can be adjusted forward whenever the _next_ QH gets
unlinked.  (uhci-hcd uses this same trick.)

Simplification of the scanning loop removes a level of indentation,
which accounts for the size of the patch.  The amount of code changed
is relatively small, and it isn't exactly a reversion of the
b963801164 commit.

This fixes Bugzilla #32432.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matej Kenda <matejken@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Following the loss of David Brownell, I volunteer to maintain the
ohci-hcd and ehci-hcd drivers.  This patch (as1472) makes it official.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1467) removes the last usages of hcd->state from
usbcore.  We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().

This fixes a regression introduced by commit
9b37596a2e860404503a3f2a6513db60c296bfdc (USB: move usbcore away from
hcd->state).  It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped.  The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped.  The solution is to ignore HC_STATE_HALT
following the handler's return.

As a consequence of this change, several of the host controller
drivers need to be modified.  They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.

The patch also changes a few of the interrupt handlers.  They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive.  Early returns were added to avoid any
confusion.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.

Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.

This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>