Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 7023 product id is the generic product id for the Etron EJ168, it is
not specific to the version found on the Asrock P67 motherboard. The same id
is e.g. also used on Gigabyte motherboards and on no-name pci-e usb-3 addon
cards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.

The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.

This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.

But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.

The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.

Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.

https://bugzilla.redhat.com/show_bug.cgi?id=1121288
https://bugzilla.kernel.org/show_bug.cgi?id=80101

Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds an extra check to ohci-hcd's I/O watchdog routine.  If
the controller stops updating the frame counter, we will assume it is
dead.  But there has to be an exception: Some controllers stop the
frame counter when no ports are connected.  Check to make sure there
is at least one active port before deciding the controller is dead.

(This test may appear racy, but it isn't.  Enabling a newly connected
port takes several milliseconds, during which time the frame counter
must advance.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dennis New <dennisn@dennisn.linuxd.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some OHCI controllers have a bug: They fail to add completed TDs to
the done queue.  Examining this queue is the only method ohci-hcd has
for telling when a transfer is complete; failure to add a TD can
result in an URB that never completes and cannot be unlinked.

This patch adds a watchdog routine to ohci-hcd.  The routine
periodically scans the active ED and TD lists, looking for TDs which
are finished but not on the done queue.  When one is found, and it is
certain that the controller hardware will never add the TD to the done
queue, the watchdog routine manually puts the TD on the done list so
that it can be handled normally.

The watchdog routine also checks for a condition indicating the
controller has died.  If the done queue is non-empty but the
HccaDoneHead pointer hasn't been updated for a few hundred
milliseconds, we assume the controller will never update it and
therefore is dead.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

URBs for a particular endpoint should complete sequentially.  That is,
we shouldn't call the completion handler for one URB until the handler
for the previous URB has returned.

When the OHCI watchdog routine is added, there will be two paths for
completing URBs: interrupt handler and watchdog routine.  Their
activities have to be synchronized so that completions don't occur in
multiple threads concurrently.

For that purpose, this patch creates an ohci_work() routine which will
be responsible for calling process_done_list() and finish_unlinks(),
the two routines that detect when an URB is complete.  Everything will
funnel through ohci_work(), and it will be careful not to run in more
than one thread at a time.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch changes the way ohci-hcd handles the TD done list.  In
addition to relying on the TD pointers stored by the controller
hardware, we need to handle TDs that the hardware has forgotten about.

This means the list has to exist even while the dl_done_list() routine
isn't running.  That function essentially gets split in two:
update_done_list() reads the TD pointers stored by the hardware and
adds the TDs to the done list, and process_done_list() scans through
the list to handle URB completions.  When we detect a TD that the
hardware forgot about, we will be able to add it to the done list
manually and then process it normally.

Since the list is really a queue, and because there can be a lot of
TDs, keep the existing singly linked implementation.  To insure that
URBs are given back in order of submission, whenever a TD is added to
the done list, all the preceding TDs for the same endpoint must be
added as well (going back to the first one that isn't already on the
done list).

The done list manipulations must all be protected by the private
lock.  The scope of the lock is expanded in preparation for the
watchdog routine to be added in a later patch.

We have to be more careful about giving back unlinked URBs.  Since TDs
may be added to the done list by the watchdog routine and not in
response to a controller interrupt, we have to check explicitly to
make sure all the URB's TDs that were added to the done list have been
processed before giving back the URB.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When an URB is unlinked from a dead controller, ohci-hcd gives back
the URB with no regard for cleaning up the internal data structures.
This won't play nicely with the upcoming changes to the TD done
list.

Therefore make ohci_urb_dequeue() call finish_unlinks(), which uses
td_done() to do a proper cleanup, rather than calling finish_urb()
directly.  Also, remove the checks that urb_priv is non-NULL; the
driver guarantees that urb_priv will never be NULL for a valid URB.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch reverts the important parts of commit 89a0fd18a96e (USB:
OHCI handles more ZFMicro quirks), namely, the parts related to
handling orphan TDs for interrupt endpoints.  A later patch in this
series will introduce a more general mechanism that applies to all
endpoint types and all controllers.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a bug in ohci-hcd.  When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule.  Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed.  If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.

This fails when a controller dies.  A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it.  The remaining URBs cannot be unlinked,
which causes the USB stack to hang.

The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running.  This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>