The USB2422 uses a different package that the USB251x and only comes in
a variant with 2 downstream ports. Other than that it is software
compatible.

Tested-by: Carsten Stelling <carsten.stelling@goerlitz.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20191023105250.16537-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The five removed symbols are unused since they were introduced in commit
3ec72a2a1e5d ("usb: misc: add USB251xB/xBi Hi-Speed Hub Controller
Driver") back in 2017.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20191023105250.16537-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the driver don't support pm_ops. These ops are not necessary
if the supply isn't switchable (always on). This assumptions seems to be
wrong because no one needs a powered hub during suspend-to-ram/disk.

So adding simple_dev_pm_ops to be able to switch off the hub during
suspend and to restore the config after a resume operation.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20190917144449.32739-5-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the reset handler was always called to deassert the reset
line because assert the line was done during probe. Now if we want to
support pm by turn of the supply we need to call this routine twice and
the i2c_lock_bus is done twice too. To simplify that we can drop the
state and just do a reset in one go. So a future pm operation don't need
to lock the i2c bus twice.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20190917144449.32739-4-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently we don't handle the supply. We need to add the supply support
to be able to switch the supply off e.g. during a suspend-to-ram
operation. So we can guarantee a correct (re-)initialization.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20190917144449.32739-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a partial revert of 73d31def1aab "usb: usb251xb: Create a ports
field collector method", which broke a existing devicetree
(arch/arm64/boot/dts/freescale/imx8mq.dtsi).

There is no reason why the swap-dx-lanes property should not apply to
the upstream port. The reason given in the breaking commit was that it's
inconsitent with respect to other port properties, but in fact it is not.
All other properties which only apply to the downstream ports explicitly
reject port 0, so there is pretty strong precedence that the driver
referred to the upstream port as port 0. So there is no inconsistency in
this property at all, other than the swapping being also applicable to
the upstream port.

CC: stable@vger.kernel.org #5.2
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190719084407.28041-3-l.stach@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This property isn't needed and not yet used anywhere. The swap-dx-lanes
property is perfectly fine for doing the swap on the upstream port
lanes.

CC: stable@vger.kernel.org #5.2
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190719084407.28041-2-l.stach@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver bindings already declare the "swap-dx-lanes" property to
invert the downstream ports lanes polarity. The similar config
can be defined for a single upstream port - "swap-us-lanes". It's
going to be boolean since there is only one upstream port
on the hub.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Seeing the ports field collection functionality is used four times per
just one function, it's better to have a dedicated method performing
the task. Note that this fix filters the port 0 out from the lanes
swapping property the same way as it has been programmed for the rest
multi-ports properties. But unlike the rest of ports config registers
the BIT(0) of the Port Lanes Swap register refers to the Upstream Port
lanes inversion. This fact hasn't been documented in the driver bindings
nor there were any mentioning about port 0 being treated as upstream
port. Lets then leave this fix as is for the properties unification
and create an additional "swap-us-lanes" in the next patch.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's pointless to scan the hub' i2c-bus segment if GPIOs aren't supported
by the system, since no GPIO-driven reset could be cleared by the driver
then. Moreover if CONFIG_GPIOLIB is disabled the gpio_chip structure
definition won't be available, which causes the incomplete type pointer
dereference compilation error. In order to fix this we need to create an
empty usb251x_check_gpio_chip() method returning zero, so the driver would
skip the i2c-bus segment checking and proceed with further probing in this
case.

Fixes: 6e3c8beb4f92 ("usb: usb251xb: Lock i2c-bus segment the hub resides")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>