Add "fsl,imx6ul-usbphy" compatible string for iMX6ul usb phy

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

of_match_device could return NULL, and so cause a NULL pointer
dereference later.

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Replace redundant variable use in return statement.

Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer
dereference. This patch avoids the oops in mxs_phy_get_vbus_status()
by aborting since there is no syscon available.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: efdbd3a5d6e ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection")
CC: <stable@vger.kernel.org> # 4.0
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The RLT code has already done it, so no software operation is needed.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

For some user cases, like plug out and replug in usb device during
the system suspend, the speed negotiation will be error due to host
doesn't know the device's disconnection, and it still hopes the
high speed device, but the device backs to "powered" state which
its high speed termination is not enabled, the usb core calls
the PHY's disconnect notifier with "full speed", it will NOT
take effect at all.

If the usb core calls disconnect notifer, the port change must happen,
so it is safe to disable high speed disconenct detector, since
connect notifier will be called soon if the device is still connected
on the port, and we will enable high speed disconnect detector at that
time.

Acked-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When we shut down the PHY, we need to power down all PHY's functions
as well as disable wakeup, it is the opposite operation we do at .init.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>