linux-toradex.git/drivers/usb/storage, branch v3.2.68

usb-storage/SCSI: blacklist FUA on JMicron 152d:2566 USB-SATA controller

2015-02-20T00:49:39+00:00

commit bf5c4136fa5ce471bdbf4cf59a813e32755fd014 upstream.

It looks like FUA support is broken on JMicron 152d:2566 bridge:

[223159.885704] sd 7:0:0:0: [sdc] Write Protect is off
[223159.885706] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08
[223159.885942] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA

[223283.691677] sd 7:0:0:0: [sdc]
[223283.691680] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[223283.691681] sd 7:0:0:0: [sdc]
[223283.691682] Sense Key : Illegal Request [current]
[223283.691684] sd 7:0:0:0: [sdc]
[223283.691685] Add. Sense: Invalid field in cdb
[223283.691686] sd 7:0:0:0: [sdc] CDB:
[223283.691687] Write(10): 2a 08 15 d0 83 0d 00 00 01 00
[223283.691690] blk_update_request: critical target error, dev sdc, sector 2927892584

This patch adds blacklist flag so that sd will not use FUA

Signed-off-by: Dmitry Nezhevenko 
Cc: Phil Dibowitz 
Cc: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb-storage: handle a skipped data phase

2014-12-14T16:23:54+00:00

commit 93c9bf4d1838d5851a18ca398b0ad66397f05056 upstream.

Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command.  Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.

This causes problems for usb-storage, for obvious reasons.  The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW.  The device won't have anything left to send, so the
command eventually times out.

The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change).  Therefore we should do our best to detect
a skipped data phase and handle it promptly.

This patch adds code to do that.  If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.

This fixes Bugzilla #86611.

Signed-off-by: Alan Stern 
CC: Matthew Dharm 
Tested-by: Paul Osmialowski 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: use US_DEBUGP() not usb_stor_dbg()]
Signed-off-by: Ben Hutchings

USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters

2014-11-05T20:27:44+00:00

commit c80b4495c61636edc58fe1ce300f09f24db28e10 upstream.

This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.

The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.

Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.

My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.

This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?

Signed-off-by: Mark Knibbs 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter

2014-11-05T20:27:44+00:00

commit b6a3ed677991558ce09046397a7c4d70530d15b3 upstream.

Hi,

The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.

I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.

Signed-off-by: Mark Knibbs 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter

2014-11-05T20:27:44+00:00

commit 67d365a57a51fb9dece6a5ceb504aa381cae1e5b upstream.

The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.

I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.

Signed-off-by: Mark Knibbs 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

storage: Add single-LUN quirk for Jaz USB Adapter

2014-11-05T20:27:42+00:00

commit c66f1c62e85927357e7b3f4c701614dcb5c498a2 upstream.

The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.

On connecting the cable a message like this appears four times in the log:
 reset full speed USB device number 4 using uhci_hcd

That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.

Signed-off-by: Mark Knibbs 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb-storage/SCSI: Add broken_fua blacklist flag

2014-08-06T17:07:33+00:00

commit b14bf2d0c0358140041d1c1805a674376964d0e0 upstream.

Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs.  This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.

Signed-off-by: Alan Stern 
Reported-by: Michael Büsch 
Tested-by: Michael Büsch 
Acked-by: James Bottomley 
CC: Matthew Dharm 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2:
 - Adjust context
 - Use sd_printk() not sd_first_printk()]
Signed-off-by: Ben Hutchings

USB: Nokia 5300 should be treated as unusual dev

2014-06-09T12:29:06+00:00

commit 6ed07d45d09bc2aa60e27b845543db9972e22a38 upstream.

Signed-off-by: Daniele Forsi 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: Nokia 305 should be treated as unusual dev

2014-06-09T12:29:06+00:00

commit f0ef5d41792a46a1085dead9dfb0bdb2c574638e upstream.

Signed-off-by: Victor A. Santos 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: storage: shuttle_usbat: fix discs being detected twice

2014-06-09T12:29:06+00:00

commit df602c2d2358f02c6e49cffc5b49b9daa16db033 upstream.

Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.

Signed-off-by: Daniele Forsi 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings