Johan writes: USB-serial fixes for 5.9-rc5 Here are some new device ids for 5.9. All have been in linux-next with no reported issues. * tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: support dynamic Quectel USB compositions USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.
Fixes: ff4a30d5e243 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.
Fixes: 7990be48ef4d ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
The issue is reported:
https://syzkaller.appspot.com/bug?id=901a0d9e6519ef8dc7acab25344bd287dd3c7be9
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com
Fixes: 217a9081d8e6 ("USB: add all configs to the "descriptors" attribute")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7a410953d1fb4dbe91ffcfdee9cbbf889d19b0d7.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1fb ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added missing code for un-register USB role switch in the remove and
error path.
Cc: Stable <stable@vger.kernel.org> # v5.8
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: 6701adfa9693b ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20200825183811.7262-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace drivers that use a SetConfiguration() request to "lightweight" reset an already configured usb device might cause data toggles to get out of sync between the device and host, and the device becomes unusable. The xHCI host requires endpoints to be dropped and added back to reset the toggle. If USB core notices the new configuration is the same as the current active configuration it will avoid these extra steps by calling usb_reset_configuration() instead of usb_set_configuration(). A SetConfiguration() request will reset the device side data toggles. Make sure usb_reset_configuration() function also drops and adds back the endpoints to ensure data toggles are in sync. To avoid code duplication split the current usb_disable_device() function and reuse the endpoint specific part. Cc: stable <stable@vger.kernel.org> Tested-by: Martin Thierer <mthierer@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB composition, defining the set of exported functions, is dynamic in newer Quectel modems. Default functions can be disabled and alternative functions can be enabled instead. The alternatives includes class functions using interface pairs, which should be handled by the respective class drivers. Active interfaces are numbered consecutively, so static blacklisting based on interface numbers will fail when the composition changes. An example of such an error, where the option driver has bound to the CDC ECM data interface, preventing cdc_ether from handling this function: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Quectel S: Product=EC25-AF C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 4 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=option E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Another device with the same id gets correct drivers, since the interface of the network function happens to be blacklisted by option: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Android S: Product=Android C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Change rules for EC21, EC25, BG96 and EG95 to match vendor specific serial functions only, to prevent binding to class functions. Require 2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET network functions. Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org>
These modules have 2 different USB layouts: The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and an ECM interface: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9205 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: AT-capable port (data). In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module exposes 6 TTY ports: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9206 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: QFLOG interface. * ttyUSB4: DAM interface. * ttyUSB5: AT-capable port (data). Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>