The intelfb driver sets color map depending on currently active pipe.
However, if an LVDS display is attached (like in laptop) the active pipe
variable is never set.  The default value is PIPE_A and can be wrong.  Set
up the pipe variable during driver initialization after hardware state was
read.

Also, the detection of the active display (and hence the pipe) is wrong.
The pipes are assigned to so called planes.  Both pipes are always enabled
on my laptop but only one plane is enabled (the plane A for the CRT or the
plane B for the LVDS).  Change active pipe detection code to take into
account a status of the plane assigned to each pipe.

The problem is visible in the 8 bpp mode if colors above 15 are used.  The
first 16 color entries are displayed correctly.

The graphics chip description is here (G45 vol. 3):
http://intellinuxgraphics.org/documentation.html

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13285

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Michal Suchanek <hramrach@centrum.cz>
Cc: Dean Menezes <samanddeanus@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Intel FB: allow odd- and even-field-first in interlaced modes, and
proper sync to vertical retrace

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Intel FB: obvious changes and corrections

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Intel FB: whitespace, bracket and other clean-ups

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Intel framebuffer now supports interlaced video modes.

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[02/07] intelfb: add GPIO registers.

Signed-off-by: Dennis Munsie <dmunsie@cecropia.com>

[04/05] intelfb: implement FBIO_WAITFORVSYNC ioctl

The (unofficial) FBIO_WAITFORVSYNC ioctl is implemented by sleeping on the appropriate waitqueue, as defined in my earlier patch. Currently, only display 0 (aka pipe A) is supported.

Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>

[03/05] intelfb: Implement basic interrupt handling

Functions have been added to enable and disable interrupts using the MMIO registers. Currently only pipe A vsync interrupts are enabled.
A generalized vsync accounting struct is defined, with the intent that it can encapsulate per-pipe vsync related info in the future. Currently a single instance is hard-coded.
The interrupt service routine currently only looks for vsync interrupts on pipe A, and increments a counter and wakes up anyone waiting on it.

This implementation is heavily influenced by similar implementations in the atyfb and matroxfb drivers.

Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>

[02/05] intelfb: Add interrupt related register definitions

Add constants for accessing HWSTAM, IER, IIR, and IMR registers.
Add constants for interrupt types supported by the 8xx and 9xx chipsets.
The registers are also stored in the hwstate struct and dumped in the debug routine.

Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>

[01/05] intelfb: Add 16-bit register access macros

This patch adds macros to read and write two-byte MMIO registers. The interrupt-related registers are all word-sized, rather than long-sized.

Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>