linux-toradex.git/drivers/video, branch v3.4.39

atmel_lcdfb: fix 16-bpp modes on older SOCs

2013-03-20T20:05:00+00:00

commit a79eac7165ed62114e6ca197195aa5060a54f137 upstream.

Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.

Use SOC-type to determine the pixel layout.

Tested on at91sam9263 and at91sam9g45.

Acked-by: Peter Korsgaard 
Signed-off-by: Johan Hovold 
Signed-off-by: Nicolas Ferre 
Signed-off-by: Greg Kroah-Hartman

fb: Yet another band-aid for fixing lockdep mess

2013-02-28T14:59:05+00:00

commit e93a9a868792ad71cdd09d75e5a02d8067473c4e upstream.

I've still got lockdep warnings even after Alan's patch, and it seems that
yet more band aids are required to paper over similar paths for
unbind_con_driver() and unregister_con_driver().  After this hack, lockdep
warnings are finally gone.

Signed-off-by: Takashi Iwai 
Cc: Alan Cox 
Cc: Florian Tobias Schandinat 
Cc: Jiri Kosina 
Tested-by: Sedat Dilek 
Signed-off-by: Andrew Morton 
Signed-off-by: Dave Airlie 
Signed-off-by: Greg Kroah-Hartman

fb: rework locking to fix lock ordering on takeover

2013-02-28T14:59:05+00:00

commit 50e244cc793d511b86adea24972f3a7264cae114 upstream.

Adjust the console layer to allow a take over call where the caller
already holds the locks.  Make the fb layer lock in order.

This is partly a band aid, the fb layer is terminally confused about the
locking rules it uses for its notifiers it seems.

[akpm@linux-foundation.org: remove stray non-ascii char, tidy comment]
[akpm@linux-foundation.org: export do_take_over_console()]
[airlied: cleanup another non-ascii char]
Signed-off-by: Alan Cox 
Cc: Florian Tobias Schandinat 
Cc: Stephen Rothwell 
Cc: Jiri Kosina 
Tested-by: Sedat Dilek 
Reviewed-by: Daniel Vetter 
Signed-off-by: Andrew Morton 
Signed-off-by: Dave Airlie 
Signed-off-by: Greg Kroah-Hartman

fbcon: don't lose the console font across generic->chip driver switch

2013-02-28T14:59:05+00:00

commit ae1287865f5361fa138d4d3b1b6277908b54eac9 upstream.

If grub2 loads efifb/vesafb, then when systemd starts it can set the console
font on that framebuffer device, however when we then load the native KMS
driver, the first thing it does is tear down the generic framebuffer driver.

The thing is the generic code is doing the right thing, it frees the font
because otherwise it would leak memory. However we can assume that if you
are removing the generic firmware driver (vesa/efi/offb), that a new driver
*should* be loading soon after, so we effectively leak the font.

However the old code left a dangling pointer in vc->vc_font.data and we
can now reuse that dangling pointer to load the font into the new
driver, now that we aren't freeing it.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340

Signed-off-by: Dave Airlie 
Cc: Kay Sievers 
Signed-off-by: Greg Kroah-Hartman

drivers/video: fsl-diu-fb: fix pixel formats for 24 and 16 bpp

2013-02-28T14:59:05+00:00

commit 5d3cc311a76073f6e0a27c0752f7e41f69e95ea7 upstream.

Framebuffer colors for 24 and 16 bpp are currently wrong. The order
of the color component arguments in the MAKE_PF() is not natural
and causes some confusion. The generated pixel format values for 24
and 16 bpp depths do not much the values in the comments.

Fix the macro arguments to be in the natural RGB order and adjust
the arguments for all depths to generate correct pixel format values
(equal to the values mentioned in the comments).

Signed-off-by: Anatolij Gustschin 
Cc: Timur Tabi 
Acked-by: Timur Tabi 
Signed-off-by: Greg Kroah-Hartman

vgacon/vt: clear buffer attributes when we load a 512 character font (v2)

2013-02-28T14:59:03+00:00

commit 2a2483072393b27f4336ab068a1f48ca19ff1c1e upstream.

When we switch from 256->512 byte font rendering mode, it means the
current contents of the screen is being reinterpreted. The bit that holds
the high bit of the 9-bit font, may have been previously set, and thus
the new font misrenders.

The problem case we see is grub2 writes spaces with the bit set, so it
ends up with data like 0x820, which gets reinterpreted into 0x120 char
which the font translates into G with a circumflex. This flashes up on
screen at boot and is quite ugly.

A current side effect of this patch though is that any rendering on the
screen changes color to a slightly darker color, but at least the screen
no longer corrupts.

v2: as suggested by hpa, always clear the attribute space, whether we
are are going to or from 512 chars.

Signed-off-by: Dave Airlie 
Signed-off-by: Greg Kroah-Hartman

drivers/video/backlight/adp88?0_bl.c: fix resume

2013-02-28T14:59:01+00:00

commit 5eb02c01bd1f3ef195989ab05e835e2b0711b5a9 upstream.

Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit.  So we need to make sure to set it again during resume,
otherwise the backlight will stay off.

Signed-off-by: Lars-Peter Clausen 
Acked-by: Michael Hennerich 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman

video: mxsfb: fix crash when unblanking the display

2013-01-17T16:50:52+00:00

commit 6c1ecba8d84841277d68140ef485335d5be28485 upstream.

The VDCTRL4 register does not provide the MXS SET/CLR/TOGGLE feature.
The write in mxsfb_disable_controller() sets the data_cnt for the LCD
DMA to 0 which obviously means the max. count for the LCD DMA and
leads to overwriting arbitrary memory when the display is unblanked.

Signed-off-by: Lothar Waßmann 
Acked-by: Juergen Beisert 
Tested-by: Lauri Hintsala 
Signed-off-by: Shawn Guo 
Signed-off-by: Greg Kroah-Hartman

viafb: don't touch clock state on OLPC XO-1.5

2012-10-21T16:27:59+00:00

commit 012a1211845eab69a5488d59eb87d24cc518c627 upstream.

As detailed in the thread titled "viafb PLL/clock tweaking causes XO-1.5
instability," enabling or disabling the IGA1/IGA2 clocks causes occasional
stability problems during suspend/resume cycles on this platform.

This is rather odd, as the documentation suggests that clocks have two
states (on/off) and the default (stable) configuration is configured to
enable the clock only when it is needed. However, explicitly enabling *or*
disabling the clock triggers this system instability, suggesting that there
is a 3rd state at play here.

Leaving the clock enable/disable registers alone solves this problem.
This fixes spurious reboots during suspend/resume behaviour introduced by
commit b692a63a.

Signed-off-by: Daniel Drake 
Signed-off-by: Florian Tobias Schandinat 
Signed-off-by: Greg Kroah-Hartman

video/udlfb: fix line counting in fb_write

2012-10-21T16:27:59+00:00

commit b8c4321f3d194469007f5f5f2b34ec278c264a04 upstream.

Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.

Signed-off-by: Alexander Holler 
Acked-by: Bernie Thompson 
Signed-off-by: Florian Tobias Schandinat 
Signed-off-by: Greg Kroah-Hartman