linux-toradex.git/drivers, branch v2.6.17.3

[PATCH] Input: return correct size when reading modalias attribute

2006-06-30T00:17:17+00:00

Input: return correct size when reading modalias attribute

Signed-off-by: Richard Purdie 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Chris Wright

[PATCH] ide-io: increase timeout value to allow for slave wakeup

2006-06-30T00:17:16+00:00

During an STR resume cycle, the ide master disk times-out when there is
also a slave present (especially CD).  Increasing the timeout in ide-io
from 10,000 to 100,000 fixes this problem.

Acked-by: Alan Cox 
Cc: Bartlomiej Zolnierkiewicz 
Cc: 
Signed-off-by: Andrew Morton 
Signed-off-by: Chris Wright

[PATCH] libata: minor patch for ATA_DFLAG_PIO

2006-06-30T00:17:16+00:00

Problem:
 - With 2.6.17 libata, some PIO-only devices are given DMA commands.

Changes:
 - Do not clear the ATA_DFLAG_PIO flag in ata_dev_configure().

Signed-off-by: Tejun Heo 
Signed-off-by: Albert Lee 
Signed-off-by: Chris Wright

[PATCH] ohci1394: Fix broken suspend/resume in ohci1394

2006-06-30T00:17:16+00:00

I've been experimenting to track down the cause of suspend/resume
problems on my Compaq Presario X1050 laptop:

http://bugzilla.kernel.org/show_bug.cgi?id=6075

Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.

I found that unloading the ohci1394 module before suspend and reloading
it after resume made the problem go away. Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:

PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was
2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was
0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was
0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was
1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was
20000100, writing 2000010a)

The default PCI driver performs the pci_restore_state when no driver is
loaded for the device. When the ohci1394 driver is loaded, it is
supposed to do this, however it appears not to do so.

I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded. I only added in
the pci_save_state and pci_restore_state - however, though I know little
of this hardware, surely the driver should really be doing more than
this when suspending and resuming? Currently it does almost nothing,
what if there are commands in progress, etc?

Signed-off-by: Robert Hancock 
Signed-off-by: Chris Wright

[PATCH] bcm43xx: init fix for possible Machine Check

2006-06-30T00:17:16+00:00

Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.

Signed-off-by: Michael Buesch 
Signed-off-by: Chris Wright

[PATCH] USB: Whiteheat: fix firmware spurious errors

2006-06-30T00:17:14+00:00

Attached patch fixes spurious errors during firmware load.

Signed-off-by: Stuart MacDonald 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Chris Wright

[PATCH] sky2: netconsole suspend/resume interaction

2006-06-17T17:52:12+00:00

A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.

This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] fix cdrom open

2006-06-17T17:44:26+00:00

Some time ago the cdrom open routine was changed so that we call the
driver's open routine before checking to see if it is read only.  However,
if we discovered that a read write open was not possible and the open
flags required a writable open, we just returned -EROFS without calling
the driver's release routine.   This seems to work for most cdrom drivers,
but breaks the Powerpc iSeries virtual cdrom rather badly.

This just inserts the release call in the error path to balance the call
to "->open()" done by "open_for_data()".

Signed-off-by: Stephen Rothwell 
Signed-off-by: Jens Axboe 
Signed-off-by: Linus Torvalds

[PATCH] sky2: stop/start hardware idle timer on suspend/resume

2006-06-13T20:16:41+00:00

The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend.  Also disable hardware IRQ's
on suspend.  Will need to revisit this with hotplug?

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: save/restore base hardware irq during suspend/resume

2006-06-13T20:16:41+00:00

The hardware should be fully shut off during suspend, and the base
irq mask restored during resume.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds