Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.

This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...

Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65b52bfd947ab29d1210314a2f6d622d

In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup
  e1000: add missing length check to e1000 receive routine
  forcedeth: add phy_power_down parameter, leave phy powered up by default (v2)
  Bluetooth: Remove useless flush_work() causing lockdep warnings

	Patch to fix bad length checking in e1000.  E1000 by default does two
things:

1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put

Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set.  This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test).  If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb.  This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU.  The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000.  This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.

The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072).  Leaving the phy
powered on is the safest default behavior.  Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.

Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Update documentation on fan_max
  hwmon: (lm78) Add missing __devexit_p()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  3c509: Add missing EISA IDs
  MAINTAINERS: take maintainership of the cpmac Ethernet driver
  net/firmare: Ignore .cis files
  ath1e: add new device id for asus hardware
  mlx4_en: Fix a kernel panic when waking tx queue
  rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle
  at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan
  mac8390: fix build with NET_POLL_CONTROLLER
  cxgb3: link fault fixes
  cxgb3: fix dma mapping regression
  netfilter: nfnetlink_log: fix wrong skbuff size	calculation
  netfilter: xt_hashlimit does a wrong SEQ_SKIP
  bfin_mac: fix build error due to net_device_ops convert
  atlx: move modinfo data from atlx.h to atl1.c
  gianfar: fix babbling rx error event bug
  cls_cgroup: read classid atomically in classifier
  netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache
  netfilter: nf_ct_tcp: fix accepting invalid RST segments

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Several EISA device IDs for 3c509 family network cards are missing from 
the driver, making the cards unusable in their EISA mode.  Here's a fix to 
add them based on the EISA configuration files distributed by 3Com and our 
eisa.ids database.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide_pci_generic: add quirk for Netcell ATA RAID