linux-toradex.git/drivers, branch v3.0.18

iwlegacy: 3945: fix hw passive scan on radar channels

2012-01-26T01:25:06+00:00

commit 68acc4afb040d98ddfd2cae0de09e2f4e1ee127f upstream.

Patch fix firmware error on "iw dev wlan0 scan passive" for
hardware scanning (with disable_hw_scan=0 module parameter).

 iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
 iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
 iwl3945 0000:03:00.0: Start IWL Error Log Dump:
 iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1
 iwl3945 0000:03:00.0: Desc       Time       asrtPC blink2 ilink1  nmiPC   Line
 iwl3945 0000:03:00.0: SYSASSERT     (0x5) 0041263900 0x13756 0x0031C 0x00000 764
 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000
 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error
 iwl3945 0000:03:00.0: Can't stop Rx DMA.

We have disable ability to change passive scanning to active on
particular channel when traffic is detected on that channel. Otherwise
firmware will report error, when we try to do passive scan on radar
channels.

Reported-and-debugged-by: Pedro Francisco 
Signed-off-by: Stanislaw Gruszka 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

iwlagn: check for SMPS mode

2012-01-26T01:25:05+00:00

commit b2ccccdca46273c7b321ecf5041c362cd950da20 upstream.

Check and report WARN only when its invalid

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=42621
https://bugzilla.redhat.com/show_bug.cgi?id=766071

Signed-off-by: Wey-Yi Guy 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

i2c-eg20t: modified the setting of transfer rate.

2012-01-26T01:25:03+00:00

commit ff35e8b18984ad2a82cbd259fc07f0be4b34b1aa upstream.

This patch modified the setting value of
I2C Bus Transfer Rate Setting Counter regisrer.

Signed-off-by: Toshiharu Okada 
Signed-off-by: Ben Dooks 
Signed-off-by: Greg Kroah-Hartman

net: Fix driver name for mdio-gpio.c

2012-01-26T01:25:03+00:00

commit f42af6c486aa5ca6ee62800cb45c5b252020509d upstream.

Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".

Signed-off-by: Dirk Eibach 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

rt2800pci: fix spurious interrupts generation

2012-01-26T01:25:02+00:00

commit dfd00c4c8f3dfa1fd7cec45f83d98b2a49743dcd upstream.

Same devices can generate interrupt without properly setting bit in
INT_SOURCE_CSR register (spurious interrupt), what will cause IRQ line
will be disabled by interrupts controller driver.

We discovered that clearing INT_MASK_CSR stops such behaviour. We
previously first read that register, and then clear all know interrupt
sources bits and do not touch reserved bits. After this patch, we write
to all register content (I believe writing to reserved bits on that
register will not cause any problems, I tested that on my rt2800pci
device).

This fix very bad performance problem, practically making device
unusable (since worked without interrupts), reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=658451

We previously tried to workaround that issue in commit
4ba7d9997869d25bd223dea7536fc1ce9fab3b3b "rt2800pci: handle spurious
interrupts", but it was reverted in commit
82e5fc2a34fa9ffea38f00c4066b7e600a0ca5e6
as thing, that will prevent to detect real spurious interrupts.

Reported-and-tested-by: Amir Hedayaty 
Signed-off-by: Stanislaw Gruszka 
Acked-by: Gertjan van Wingerde 
Signed-off-by: John W. Linville 
Signed-off-by: Greg Kroah-Hartman

I2C: OMAP: correct SYSC register offset for OMAP4

2012-01-26T01:25:01+00:00

commit 2727b1753934e154931d6b3bdf20c9b2398457a2 upstream.

Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.

Signed-off-by: Alexander Aring 
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman 
Signed-off-by: Greg Kroah-Hartman

target: Set additional sense length field in sense data

2012-01-26T01:25:00+00:00

commit 895f3022523361e9b383cf48f51feb1f7d5e7e53 upstream.

The target code was not setting the additional sense length field in the
sense data it returned, which meant that at least the Linux stack
ignored the ASC/ASCQ fields.  For example, without this patch, on a
tcm_loop device:

    # sg_raw -v /dev/sda 2 0 0 0 0 0

gives

        cdb to send: 02 00 00 00 00 00
    SCSI Status: Check Condition

    Sense Information:
     Fixed format, current;  Sense key: Illegal Request
      Raw sense data (in hex):
            70 00 05 00 00 00 00 00

while after the patch we correctly get the following (which matches what
a regular disk returns):

        cdb to send: 02 00 00 00 00 00
    SCSI Status: Check Condition

    Sense Information:
     Fixed format, current;  Sense key: Illegal Request
     Additional sense: Invalid command operation code
     Raw sense data (in hex):
            70 00 05 00 00 00 00 0a  00 00 00 00 20 00 00 00
            00 00

Signed-off-by: Roland Dreier 
Signed-off-by: Nicholas Bellinger 
Signed-off-by: Greg Kroah-Hartman

target: Set response format in INQUIRY response

2012-01-26T01:25:00+00:00

commit ce136176fea522fc8f4c16dcae7e8ed1d890ca39 upstream.

Current SCSI specs say that the "response format" field in the standard
INQUIRY response should be set to 2, and all the real SCSI devices I
have do put 2 here.  So let's do that too.

Signed-off-by: Roland Dreier 
Signed-off-by: Nicholas Bellinger 
Signed-off-by: Greg Kroah-Hartman

sym53c8xx: Fix NULL pointer dereference in slave_destroy

2012-01-26T01:24:59+00:00

commit cced5041ed5a2d1352186510944b0ddfbdbe4c0b upstream.

sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).

Signed-off-by: Stratos Psomadakis 
Signed-off-by: James Bottomley 
Signed-off-by: Greg Kroah-Hartman

ACPI: processor: fix acpi_get_cpuid for UP processor

2012-01-26T01:24:59+00:00

commit d640113fe80e45ebd4a5b420b220d3f6bf37f682 upstream.

For UP processor, it is likely that no _MAT method or MADT table defined.
So currently acpi_get_cpuid(...) always return -1 for UP processor.
This is wrong. It should return valid value for CPU0.

In the other hand, BIOS may define multiple CPU handles even for UP
processor, for example

        Scope (_PR)
        {
            Processor (CPU0, 0x00, 0x00000410, 0x06) {}
            Processor (CPU1, 0x01, 0x00000410, 0x06) {}
            Processor (CPU2, 0x02, 0x00000410, 0x06) {}
            Processor (CPU3, 0x03, 0x00000410, 0x06) {}
        }

We should only return valid value for CPU0's acpi handle.
And return invalid value for others.

http://marc.info/?t=132329819900003&r=1&w=2

Reported-and-tested-by: wallak@free.fr
Signed-off-by: Lin Ming 
Signed-off-by: Len Brown 
Signed-off-by: Greg Kroah-Hartman