linux-toradex.git/drivers, branch v3.14.46

lpfc: Add iotag memory barrier

2015-06-29T19:25:37+00:00

commit 27f344eb15dd0da80ebec80c7245e8c85043f841 upstream.

Add a memory barrier to ensure the valid bit is read before
any of the cqe payload is read. This fixes an issue seen
on Power where the cqe payload was getting loaded before
the valid bit. When this occurred, we saw an iotag out of
range error when a command completed, but since the iotag
looked invalid the command didn't get completed to scsi core.
Later we hit the command timeout, attempted to abort the command,
then waited for the aborted command to get returned. Since the
adapter already returned the command, we timeout waiting,
and end up escalating EEH all the way to host reset. This
patch fixes this issue.

Signed-off-by: Brian King 
Signed-off-by: James Smart 
Signed-off-by: Christoph Hellwig 
Signed-off-by: Greg Kroah-Hartman

ath3k: add support of 13d3:3474 AR3012 device

2015-06-29T19:25:37+00:00

commit 0d0cef6183aec0fb6d0c9f00a09ff51ee086bbe2 upstream.

BugLink: https://bugs.launchpad.net/bugs/1427680

This device requires new firmware files
 AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3474 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Dmitry Tunin 
Signed-off-by: Marcel Holtmann 
Signed-off-by: Greg Kroah-Hartman

ath3k: Add support of 0489:e076 AR3012 device

2015-06-29T19:25:37+00:00

commit 692c062e7c282164fd7cda68077f79dafd176eaf upstream.

BugLink: https://bugs.launchpad.net/bugs/1462614

This device requires new firmware files
 AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.

T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=06 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e076 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms

Signed-off-by: Dmitry Tunin 
Signed-off-by: Marcel Holtmann 
Signed-off-by: Greg Kroah-Hartman

drm/mgag200: Reject non-character-cell-aligned mode widths

2015-06-29T19:25:37+00:00

commit 25161084b1c1b0c29948f6f77266a35f302196b7 upstream.

Turns out 1366x768 does not in fact work on this hardware.

Signed-off-by: Adam Jackson 
Signed-off-by: Dave Airlie 
Signed-off-by: Greg Kroah-Hartman

crypto: caam - fix RNG buffer cache alignment

2015-06-29T19:25:37+00:00

commit 412c98c1bef65fe7589f1300e93735d96130307c upstream.

The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.

This fix aligns the buffers inside the struct.

Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.

Signed-off-by: Steve Cornelius 
Signed-off-by: Victoria Milhoan 
Signed-off-by: Herbert Xu 
Signed-off-by: Greg Kroah-Hartman

serial: imx: Fix DMA handling for IDLE condition aborts

2015-06-23T00:01:23+00:00

commit 392bceedb107a3dc1d4287e63d7670d08f702feb upstream.

The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.

This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.

Reported-by: Peter Seiderer 
Signed-off-by: Philipp Zabel 
Tested-by: Fabio Estevam 
Signed-off-by: Greg Kroah-Hartman

drm/radeon: fix freeze for laptop with Turks/Thames GPU.

2015-06-23T00:01:23+00:00

commit 6dfd197283bffc23a2b046a7f065588de7e1fc1e upstream.

Laptop with Turks/Thames GPU will freeze if dpm is enabled. It seems
the SMC engine is relying on some state inside the CP engine. CP needs
to chew at least one packet for it to get in good state for dynamic
power management.

This patch simply disabled and re-enable DPM after the ring test which
is enough to avoid the freeze.

Signed-off-by: Jérôme Glisse 
Signed-off-by: Alex Deucher 
Signed-off-by: Greg Kroah-Hartman

drm/i915: Fix DDC probe for passive adapters

2015-06-23T00:01:23+00:00

commit 3f5f1554ee715639e78d9be87623ee82772537e0 upstream.

Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.

That, however, was thwarted by the fix for [1]:

commit 9292f37e1f5c79400254dca46f83313488093825
Author: Eugeni Dodonov 
Date:   Thu Jan 5 09:34:28 2012 -0200

    drm: give up on edid retries when i2c bus is not responding

This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).

Since its introduction in

commit f899fc64cda8569d0529452aafc0da31c042df2e
Author: Chris Wilson 
Date:   Tue Jul 20 15:44:45 2010 -0700

    drm/i915: use GMBUS to manage i2c links

we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.

Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.

This patch is based on the work, and commit message, by Todd Previte
.

[1] https://bugs.freedesktop.org/show_bug.cgi?id=41059

v2: Don't retry if using bit banging.

v3: Move retry within gmbux_xfer, retry only on first message.

v4: Initialize GMBUS0 on retry (Ville).

v5: Take index reads into account (Ville).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924
Cc: Todd Previte 
Tested-by: Oliver Grafe  (v2)
Tested-by: Jim Bride 
Reviewed-by: Ville Syrjälä 
Signed-off-by: Jani Nikula 
Signed-off-by: Greg Kroah-Hartman

drm/i915/hsw: Fix workaround for server AUX channel clock divisor

2015-06-23T00:01:23+00:00

commit e058c945e03a629c99606452a6931f632dd28903 upstream.

According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset.  This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.

[v2] Implemented alternate solution suggested by Jani Nikula.

Signed-off-by: Jim Bride 
Signed-off-by: Jani Nikula 
Signed-off-by: Greg Kroah-Hartman

pata_octeon_cf: fix broken build

2015-06-23T00:01:22+00:00

commit 4710f2facb5c68d629015747bd09b37203e0d137 upstream.

MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.

Signed-off-by: Aaro Koskinen 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman