linux-toradex.git/fs/dlm/lockspace.c, branch v3.10.78

dlm: don't use idr_remove_all()

2013-02-28T03:10:13+00:00

idr_destroy() can destroy idr by itself and idr_remove_all() is being
deprecated.

The conversion isn't completely trivial for recover_idr_clear() as it's
the only place in kernel which makes legitimate use of idr_remove_all()
w/o idr_destroy().  Replace it with idr_remove() call inside
idr_for_each_entry() loop.  It goes on top so that it matches the
operation order in recover_idr_del().

Signed-off-by: Tejun Heo 
Cc: Christine Caulfield 
Cc: David Teigland 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

dlm: fix unlock balance warnings

2012-08-08T16:33:49+00:00

The in_recovery rw_semaphore has always been acquired and
released by different threads by design.  To work around
the "BUG: bad unlock balance detected!" messages, adjust
things so the dlm_recoverd thread always does both down_write
and up_write.

Signed-off-by: David Teigland

dlm: fix race between remove and lookup

2012-07-16T19:18:01+00:00

It was possible for a remove message on an old
rsb to be sent after a lookup message on a new
rsb, where the rsbs were for the same resource
name.  This could lead to a missing directory
entry for the new rsb.

It is fixed by keeping a copy of the resource
name being removed until after the remove has
been sent.  A lookup checks if this in-progress
remove matches the name it is looking up.

Signed-off-by: David Teigland

dlm: use idr instead of list for recovered rsbs

2012-07-16T19:17:52+00:00

When a large number of resources are being recovered,
a linear search of the recover_list takes a long time.
Use an idr in place of a list.

Signed-off-by: David Teigland

dlm: use rsbtbl as resource directory

2012-07-16T19:16:19+00:00

Remove the dir hash table (dirtbl), and use
the rsb hash table (rsbtbl) as the resource
directory.  It has always been an unnecessary
duplication of information.

This improves efficiency by using a single rsbtbl
lookup in many cases where both rsbtbl and dirtbl
lookups were needed previously.

This eliminates the need to handle cases of rsbtbl
and dirtbl being out of sync.

In many cases there will be memory savings because
the dir hash table no longer exists.

Signed-off-by: David Teigland

dlm: fixes for nodir mode

2012-05-02T19:15:27+00:00

The "nodir" mode (statically assign master nodes instead
of using the resource directory) has always been highly
experimental, and never seriously used.  This commit
fixes a number of problems, making nodir much more usable.

- Major change to recovery: recover all locks and restart
  all in-progress operations after recovery.  In some
  cases it's not possible to know which in-progess locks
  to recover, so recover all.  (Most require recovery
  in nodir mode anyway since rehashing changes most
  master nodes.)

- Change the way nodir mode is enabled, from a command
  line mount arg passed through gfs2, into a sysfs
  file managed by dlm_controld, consistent with the
  other config settings.

- Allow recovering MSTCPY locks on an rsb that has not
  yet been turned into a master copy.

- Ignore RCOM_LOCK and RCOM_LOCK_REPLY recovery messages
  from a previous, aborted recovery cycle.  Base this
  on the local recovery status not being in the state
  where any nodes should be sending LOCK messages for the
  current recovery cycle.

- Hold rsb lock around dlm_purge_mstcpy_locks() because it
  may run concurrently with dlm_recover_master_copy().

- Maintain highbast on process-copy lkb's (in addition to
  the master as is usual), because the lkb can switch
  back and forth between being a master and being a
  process copy as the master node changes in recovery.

- When recovering MSTCPY locks, flag rsb's that have
  non-empty convert or waiting queues for granting
  at the end of recovery.  (Rename flag from LOCKS_PURGED
  to RECOVER_GRANT and similar for the recovery function,
  because it's not only resources with purged locks
  that need grant a grant attempt.)

- Replace a couple of unnecessary assertion panics with
  error messages.

Signed-off-by: David Teigland

dlm: add recovery callbacks

2012-01-04T14:56:31+00:00

These new callbacks notify the dlm user about lock recovery.
GFS2, and possibly others, need to be aware of when the dlm
will be doing lock recovery for a failed lockspace member.

In the past, this coordination has been done between dlm and
file system daemons in userspace, which then direct their
kernel counterparts.  These callbacks allow the same
coordination directly, and more simply.

Signed-off-by: David Teigland

dlm: add node slots and generation

2012-01-04T14:55:57+00:00

Slot numbers are assigned to nodes when they join the lockspace.
The slot number chosen is the minimum unused value starting at 1.
Once a node is assigned a slot, that slot number will not change
while the node remains a lockspace member.  If the node leaves
and rejoins it can be assigned a new slot number.

A new generation number is also added to a lockspace.  It is
set and incremented during each recovery along with the slot
collection/assignment.

The slot numbers will be passed to gfs2 which will use them as
journal id's.

Signed-off-by: David Teigland

dlm: convert rsb list to rb_tree

2011-11-18T16:20:15+00:00

Change the linked lists to rb_tree's in the rsb
hash table to speed up searches.  Slow rsb searches
were having a large impact on gfs2 performance due
to the large number of dlm locks gfs2 uses.

Signed-off-by: Bob Peterson 
Signed-off-by: David Teigland

dlm: use workqueue for callbacks

2011-07-15T17:30:43+00:00

Instead of creating our own kthread (dlm_astd) to deliver
callbacks for all lockspaces, use a per-lockspace workqueue
to deliver the callbacks.  This eliminates complications and
slowdowns from many lockspaces sharing the same thread.

Signed-off-by: David Teigland