Extend struct dw_hdmi_qp_plat_data to include the supported display
output formats and maximum bits per color channel.  When provided by the
platform driver, use them to setup the HDMI bridge accordingly.

Additionally, improve debug logging in dw_hdmi_qp_bridge_atomic_enable()
to also show the current HDMI output format and bpc.

Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251021-rk3588-10bpc-v3-2-3d3eed00a6db@collabora.com

Currently the TIMER_BASE_CONFIG0 register gets initialized to a fixed
value as initially found in vendor driver code supporting the RK3588
SoC.  As a matter of fact the value matches the rate of the HDMI TX
reference clock, which is roughly 428.57 MHz.

However, on RK3576 SoC that rate is slightly lower, i.e. 396.00 MHz, and
the incorrect register configuration breaks CEC functionality.

Set the timer base according to the actual reference clock rate that
shall be provided by the platform driver.  Otherwise fallback to the
vendor default.

While at it, also drop the unnecessary empty lines in
dw_hdmi_qp_init_hw().

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-2-fa25163c4b08@collabora.com

Add support for the CEC interface of the Synopsys DesignWare HDMI QP TX
controller.

This is based on the downstream implementation, but rewritten on top of
the CEC helpers added recently to the DRM HDMI connector framework.

Also note struct dw_hdmi_qp_plat_data has been extended to include the
CEC IRQ number to be provided by the platform driver.

Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Co-developed-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Derek Foreman <derek.foreman@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-1-fa25163c4b08@collabora.com

Updating drm-misc-next to the state of v6.18-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

The HDMI TX Parallel Audio Interface (HTX_PAI) is a digital module that
acts as the bridge between the Audio Subsystem to the HDMI TX Controller.
This IP block is found in the HDMI subsystem of the i.MX8MP SoC.

Data received from the audio subsystem can have an arbitrary component
ordering. The HTX_PAI block has integrated muxing options to select which
sections of the 32-bit input data word will be mapped to each IEC60958
field. The HTX_PAI_FIELD_CTRL register contains mux selects to
individually select P,C,U,V,Data, and Preamble.

Use component helper so that imx8mp-hdmi-tx will be aggregate driver,
imx8mp-hdmi-pai will be component driver, then imx8mp-hdmi-pai can use
bind() ops to get the plat_data from imx8mp-hdmi-tx device.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-6-shengjiu.wang@nxp.com

Add API dw_hdmi_set_sample_iec958() for IEC958 format because audio device
driver needs IEC958 information to configure this specific setting.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-5-shengjiu.wang@nxp.com

Add API dw_hdmi_to_plat_data() to fetch plat_data because audio device
driver needs it to enable(disable)_audio().

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-4-shengjiu.wang@nxp.com

Add support for Exynos7870's DSIM IP block in the bridge driver.

Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Presently, all devices refer to clock names from a single array. The
only controlling parameter is the number of clocks (num_clks field of
samsung_dsim_driver_data) which uses the first n clocks of that array.
As new devices are added, this approach turns out to be cumbersome.

Separate the clock names in individual arrays required by each variant,
in a struct clk_bulk_data. Add a pointer field to the driver data struct
which points to their respective clock names, and rework the clock usage
code to use the clk_bulk_* API instead.

Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The PLL_STABLE bit of DSIM_DPHY_STATUS is hardcoded to BIT(31), but
Exynos7870's DSIM has it in BIT(24) as per downstream kernel sources.

In order to support both, move this bit value to the driver data struct
and define it for every driver compatible. Reference the value from
there instead, in functions wherever required.

Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>