This is the 4.4.107 stable release

[ Upstream commit d97556c8012015901a3ce77f46960078139cd79d ]

We need to also have OFFPULLUDENABLE bit set to use the off mode pull values.
Otherwise the line is pulled down internally if no external pull exists.

This is has some documentation at:

http://processors.wiki.ti.com/index.php/Optimizing_OMAP35x_and_AM/DM37x_OFF_mode_PAD_configuration

Note that the value is still glitchy during off mode transitions as documented
in spz319f.pdf "Advisory 1.45". It's best to use external pulls instead of
relying on the internal ones for off mode and even then anything pulled up
will get driven down momentarily on off mode restore for GPIO banks other
than bank1.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for clock gating of the ESW(Ethernet switch) peripheral.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

The 2-bit gates found i.MX and Vybrid SoC support different clock
configuration:

0b00: clk disabled
0b01: clk enabled in RUN mode but disabled in WAIT and STOP mode
0b10: clk enabled in RUN, WAIT and STOP mode (only Vybrid)
0b11: clk enabled in RUN and WAIT mode

For some clocks, we might want to configure different behaviour,
e.g. a memory clock should be on even in STOP mode. Add a new
function imx_clk_gate2_cgr which allow to configure specific
gate values through the cgr_val parameter.

Add the ipg (bus) clock for the TCON modules (Timing Controller). This
module is required by the new DCU DRM driver, since the display signals
pass through TCON.

Signed-off-by: Stefan Agner <stefan@agner.ch>

Pull ARM DT updates from Olof Johansson:
 "As usual, this is the massive branch we have for each release.  Lots
  of various updates and additions of hardware descriptions on existing
  hardware, as well as the usual additions of new boards and SoCs.

  This is also the first release where we've started mixing 64- and
  32-bit DT updates in one branch.

  (Specific details on what's actually here and new is pretty easy to
  tell from the diffstat, so there's little point in duplicating listing
  it here)"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
  ARM: dts: uniphier: add system-bus-controller nodes
  ARM64: juno: disable NOR flash node by default
  ARM: dts: uniphier: add outer cache controller nodes
  arm64: defconfig: Enable PCI generic host bridge by default
  arm64: Juno: Add support for the PCIe host bridge on Juno R1
  Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
  ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
  dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
  dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
  dts/ls2080a: Update Simulator DTS to add support of various peripherals
  dts/ls2080a: Remove text about writing to Free Software Foundation
  dts/ls2080a: Update DTSI to add support of various peripherals
  doc: DTS: Update DWC3 binding to provide reference to generic bindings
  doc/bindings: Update GPIO devicetree binding documentation for LS2080A
  Documentation/dts: Move FSL board-specific bindings out of /powerpc
  Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
  arm64: Rename FSL LS2085A SoC support code to LS2080A
  arm64: Use generic Layerscape SoC family naming
  ARM: dts: uniphier: add ProXstream2 Vodka board support
  ARM: dts: uniphier: add ProXstream2 Gentil board support
  ...

Pull ARM SoC driver updates from Olof Johansson:
 "As we've enabled multiplatform kernels on ARM, and greatly done away
  with the contents under arch/arm/mach-*, there's still need for
  SoC-related drivers to go somewhere.

  Many of them go in through other driver trees, but we still have
  drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
  that might be shared between ARM and ARM64 (or just in general makes
  sense to not have under the architecture directory).

  This branch contains mostly such code:

   - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
     communicate with power management blocks on these SoCs for use by
     clock, regulator and bus frequency drivers.

   - Allwinner Reduced Serial Bus driver, again used to communicate with
     PMICs.

   - Drivers for ARM's SCPI (System Control Processor).  Not to be
     confused with PSCI (Power State Coordination Interface).  SCPI is
     used to communicate with the assistant embedded cores doing power
     management, and we have yet to see how many of them will implement
     this for their hardware vs abstracting in other ways (or not at all
     like in the past).

   - To make confusion between SCPI and PSCI more likely, this release
     also includes an update of PSCI to interface version 1.0.

   - Rockchip support for power domains.

   - A driver to talk to the firmware on Raspberry Pi"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
  soc: qcom: smd-rpm: Correct size of outgoing message
  bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
  bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
  ARM: bcm2835: add mutual inclusion protection
  drivers: psci: make PSCI 1.0 functions initialization version dependent
  dt-bindings: Correct paths in Rockchip power domains binding document
  soc: rockchip: power-domain: don't try to print the clock name in error case
  soc: qcom/smem: add HWSPINLOCK dependency
  clk: berlin: add cpuclk
  ARM: berlin: dts: add CLKID_CPU for BG2Q
  ARM: bcm2835: Add the Raspberry Pi firmware driver
  soc: qcom: smem: Move RPM message ram out of smem DT node
  soc: qcom: smd-rpm: Correct the active vs sleep state flagging
  soc: qcom: smd: delete unneeded of_node_put
  firmware: qcom-scm: build for correct architecture level
  soc: qcom: smd: Correct SMEM items for upper channels
  qcom-scm: add missing prototype for qcom_scm_is_available()
  qcom-scm: fix endianess issue in __qcom_scm_is_call_available
  soc: qcom: smd: Reject send of too big packets
  soc: qcom: smd: Handle big endian CPUs
  ...

Pull input updates from Dmitry Torokhov:
 "Items of note:

   - evdev users can now limit or mask the kind of events they will
     receive.  This will allow applications such as power manager or
     network manager to only be woken when user presses special keys
     such as KEY_POWER or KEY_WIFI and not be bothered with ordinary
     key presses coming from keyboard

   - support for FocalTech FT6236 touchscreen controller

   - support for ROHM BU21023/24 touchscreen controller

   - edt-ft5x06 touchscreen driver got a face lift and can now be used
     with FT5506

   - support for Google Fiber TV Box remote controls

   - improvements in xpad driver (with more to come)

   - several parport-based drivers have been switched to the new device
     model

   - other miscellaneous driver improvements"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
  HID: hid-gfrm: avoid warning for input_configured API change
  HID: hid-input: allow input_configured callback return errors
  Input: evdev - fix bug in checking duplicate clock change request
  Input: add userio module
  Input: evdev - add event-mask API
  Input: snvs_pwrkey - remove duplicated semicolon
  HID: hid-gfrm: Google Fiber TV Box remote controls
  Input: e3x0-button - update Kconfig description
  Input: tegra-kbc - drop use of IRQF_NO_SUSPEND flag
  Input: tegra-kbc - enable support for the standard "wakeup-source" property
  Input: xen - check return value of xenbus_printf
  Input: hp_sdc_rtc - fix y2038 problem in proc_show
  Input: nomadik-ske-keypad - fix a trivial typo
  Input: xpad - fix clash of presence handling with LED setting
  Input: edt-ft5x06 - work around FT5506 firmware bug
  Input: edt-ft5x06 - add support for FT5506
  Input: edt-ft5x06 - add support for different max support points
  Input: edt-ft5x06 - use max support points to determine how much to read
  Input: rotary-encoder - add support for quarter-period mode
  Input: rotary-encoder - use of_property_read_bool
  ...