Fix the clock enable/disable tracking in the AMBA CLCD driver so
that the driver doesn't try to disable an already disabled clock,
thereby causing the clock (if shared) to become unbalanced.

This resolves a problem with CLCD on LPC32xx ARM platforms.

Reported-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/mm/init.c

Some platforms gate the pclk (APB - the bus - clock) to the peripherals
for power saving, along with the functional clock.  When devices are
accessed without pclk enabled, the kernel will oops.

This gives them two options:

1. Leave all clocks on all the time.
2. Attempt to gate pclk along with the functional clock.

(With some hardware, pclk and the functional clock are gated by a single
bit in a register.)

(1) has the disadvantage that it causes increased power usage, which is
bad news for battery operated devices.  (2) can lead to kernel oops if
registers are accessed without the functional clock being enabled.

So, introduce the apb_pclk signal in such a way existing drivers don't
need to be updated.  Essentially, this means we guarantee that:

1. pclk will be enabled whenever the driver is bound to a device -
   from probe() to remove() time.
2. pclk will also be enabled when reading the primecell IDs from the device.

In order to allow drivers to be incrementally updated to achieve greater
power savings, we provide two additional calls to allow drivers to
manage the pclk - amba_pclk_enable()/amba_pclk_disable().

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Platforms may have some external power control which need to be
controlled from board specific code.  Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.

Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.

Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.

Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  DMAENGINE: DMA40 U8500 platform configuration
  DMA: PL330: Add dma api driver

This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The PL022 SPI driver did not cleanly separate between the
original unmodified ARM version and the ST Microelectronics
versions. Split this more cleanly and fix some whitespace
moaning from checkpatch at the same time.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>