Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

Support pm_ops in the AMBA bus, required to allow drivers to use runtime pm.
The implementation of AMBA bus pm ops is based on the platform bus
implementation.

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Now that the bus level code deals with a const id table, we can also
make the ID table in the amba_driver structure also const.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make Primecell driver probe functions take a const pointer to their
ID tables.  Drivers should never modify their ID tables in their
probe handler.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Export amba_bustype struct so it can be used for things like registering
bus notifiers.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARM CLCD PL110 controller in TFT mode provides two output formats
based on whether the controller is in 24bpp mode or not - either 5551
or 888.  PL111 augments this with a 444 and 565 modes.

Some implementations provide an external MUX on the PL110 output to
reassign the bits to achieve 565 mode.

Provide a system of capability flags to allow the CLCD driver to work
out what is supported by each panel and board, and therefore which
display formats are permitted.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Instead of matching the entire peripheral ID, match against
just the part number using the amba_xxx() macros.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Based on a patch from Linus Walleij.

Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface.  The changes over Linus' driver are:

- rename txsize_threshold to dmasize_threshold, as this reflects the
  purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer.  Some DMA controllers
  (eg, PL08x) are unable to be configured for scatter DMA and also listen
  to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
  They can do one or other but not both.  As MMCI uses LBREQ/LSREQ for the
  final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
  MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
  function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
  pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
  is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
  set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
  its own restrictions on buffer alignment, not the individual DMA engine
  users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
  causes LBREQ to be asserted for the last seven transfers, rather than
  six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
  transfer size required to complete the DMA operation.

Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>