In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:

- We add timer for polling. If we set poll_timer to 10, every 10ms,
 timer handler checks the residue in the dma buffer and transfer data
 to the tty. Also, last_residue is updated for the next polling.

- poll_timeout is used to prevent the timer's system cost.
  If poll_timeout is set to 3000 and no data is received in 3 seconds,
  we inactivate poll timer and driver falls back to interrupt-driven.
  When data is received again in FIFO and UART irq is occurred, we switch
  back to DMA mode and start polling.

- We use consistent DMA mappings to avoid from the frequent cache operation
  of the timer function for default.

- pl011_dma_rx_chars is modified. the pending size is recalculated because
  data can be taken by polling.

- the polling time is adjusted if dma rx poll is enabled but no rate is
  specified. Ideal polling interval to push 1 character at every interval
  is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
  per sec'. But It is very aggressive to system. Experimentally,
 '10000000 / baud' is suitable to receive dozens of characters. the poll rate
 can be specified statically by dma_rx_poll_rate of the platform data as well.

Changes compared to v1:
 - Use of consistent DMA mappings.
 - Added dma_rx_poll_rate in platform data to specify the polling interval.
 - Added dma_rx_poll_timeout in platform data to specify the polling timeout.

Changes compared to v2:
 - Use of consistent DMA mappings for default.
 - Added dma_rx_poll_enable in platform data to adjust the polling time
   according to the baud rate.
 - remove unnecessary lock from the polling function.

Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull slave-dmaengine updates from Vinod Koul:
 "This is fairly big pull by my standards as I had missed last merge
  window.  So we have the support for device tree for slave-dmaengine,
  large updates to dw_dmac driver from Andy for reusing on different
  architectures.  Along with this we have fixes on bunch of the drivers"

Fix up trivial conflicts, usually due to #include line movement next to
each other.

* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
  Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
  ARM: dts: pl330: Add #dma-cells for generic dma binding support
  DMA: PL330: Register the DMA controller with the generic DMA helpers
  DMA: PL330: Add xlate function
  DMA: PL330: Add new pl330 filter for DT case.
  dma: tegra20-apb-dma: remove unnecessary assignment
  edma: do not waste memory for dma_mask
  dma: coh901318: set residue only if dma is in progress
  dma: coh901318: avoid unbalanced locking
  dmaengine.h: remove redundant else keyword
  dma: of-dma: protect list write operation by spin_lock
  dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
  dma: of-dma.c: fix memory leakage
  dw_dmac: apply default dma_mask if needed
  dmaengine: ioat - fix spare sparse complain
  dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
  ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
  dw_dmac: add support for Lynxpoint DMA controllers
  dw_dmac: return proper residue value
  dw_dmac: fill individual length of descriptor
  ...

Since it is now used by code under drivers/clk/ it makes sense for this
file to be in a more generic location. This is required for building
vexpress support on arm64.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>

The header is used by drivers/dma/amba-pl08x.c, which can be compiled
under x86, where PL080 exists under a PCI-to-AMBA bridge. This patche
moves it where it can be accessed by other architectures, and fixes
all users.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This creates amba_apb_device_add_res() and
amba_ahb_device_add_res() respectively, to add devices with
another parent than iomem_resource. This is needed to specify
that a device is contained in a specific IO range.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull spi updates from Mark Brown:
 "No framework work here, only a bunch of driver updates of varying
  sizes:

   - Factoring out of the core hardware support from the MXS MMC driver
     by Marek Vasut to allow the hardware to also be used for SPI.
   - Lots of error handling cleanups from Guenter Roeck
   - Removal of the existing Tegra driver which is quite comprehensively
     broken as detailed in the changelog for the removal.
   - DT suppport for the PL022 and GPIO drivers.
   - pinctrl support for OMAP and PL022."

Pulling from Mark Brown as Grant Likely is still busy moving.

* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
  spi: remove completely broken Tegra driver
  spi/imx: set the inactive state of the clock according to the clock polarity
  spi/pl022: get/put resources on suspend/resume
  spi/pl022: use more managed resources
  spi/pl022: Devicetree support w/o platform data
  spi/s3c64xx: Don't free controller_data on non-dt platforms
  spi: omap2-mcspi: add pinctrl support
  spi/pl022: adopt pinctrl support
  spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
  spi/gpio: Fix stub for spi_gpio_probe_dt()
  spi/mxs: Make the SPI block clock speed configurable via DT
  spi: spi-sh-hspi: drop frees of devm_ alloc'd data
  spi/pl022: Fix chipselects pointer computation
  spi: spi-tle62x0: Use module_spi_driver macro
  mxs/spi: Rework the mxs_ssp_timeout to be more readable
  mxs/spi: Decrement the DMA/PIO border
  mxs/spi: Increment the transfer length only if transfer succeeded
  mxs/spi: Fix issues when doing long continuous transfer
  spi: spi-gpio: Add DT bindings
  spi: spi-gpio: store chipselect information in private structure
  ...

Since commit 4fd0690bb0c3955983560bb2767ee82e2b197f9b
"serial: pl011: implement workaround for CTS clear event issue"
the PL011 UART is no longer at risk to hang up, so get rid
of the callback altogether.

Cc: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds the ability for the driver to control the chip select directly.
This enables independence from cs_control callbacks.  Configurable via
platform_data, to be extended as DT in the following patch.

Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>

Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pull ARM DMA engine updates from Russell King:
 "This looks scary at first glance, but what it is is:
   - a rework of the sa11x0 DMA engine driver merged during the previous
     cycle, to extract a common set of helper functions for DMA engine
     implementations.
   - conversion of amba-pl08x.c to use these helper functions.
   - addition of OMAP DMA engine driver (using these helper functions),
     and conversion of some of the OMAP DMA users to use DMA engine.

  Nothing in the helper functions is ARM specific, so I hope that other
  implementations can consolidate some of their code by making use of
  these helpers.

  This has been sitting in linux-next most of the merge cycle, and has
  been tested by several OMAP folk.  I've tested it on sa11x0 platforms,
  and given it my best shot on my broken platforms which have the
  amba-pl08x controller.

  The last point is the addition to feature-removal-schedule.txt, which
  will have a merge conflict.  Between myself and TI, we're planning to
  remove the old TI DMA implementation next year."

Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}

* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
  ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
  ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
  Add feature removal of old OMAP private DMA implementation
  mtd: omap2: remove private DMA API implementation
  mtd: omap2: add DMA engine support
  spi: omap2-mcspi: remove private DMA API implementation
  spi: omap2-mcspi: add DMA engine support
  ARM: omap: remove mmc platform data dma_mask and initialization
  mmc: omap: remove private DMA API implementation
  mmc: omap: add DMA engine support
  mmc: omap_hsmmc: remove private DMA API implementation
  mmc: omap_hsmmc: add DMA engine support
  dmaengine: omap: add support for cyclic DMA
  dmaengine: omap: add support for setting fi
  dmaengine: omap: add support for returning residue in tx_state method
  dmaengine: add OMAP DMA engine driver
  dmaengine: sa11x0-dma: add cyclic DMA support
  dmaengine: sa11x0-dma: fix DMA residue support
  dmaengine: PL08x: ensure all descriptors are freed when channel is released
  dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
  ...

Remove the unused fields from struct ssp_config_chip that was removed
before
Add bus_id documentation to pl022_ssp_controller

Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>