Some engines optimize operation by reading ahead in the descriptor chain
such that descriptor2 may start execution before descriptor1 completes.
If descriptor2 depends on the result from descriptor1 then a fence is
required (on descriptor2) to disable this optimization.  The async_tx
api could implicitly identify dependencies via the 'depend_tx'
parameter, but that would constrain cases where the dependency chain
only specifies a completion order rather than a data dependency.  So,
provide an ASYNC_TX_FENCE to explicitly identify data dependencies.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>

 async_raid6_2data_recov() recovers two data disk failures

 async_raid6_datap_recov() recovers a data disk and the P disk

These routines are a port of the synchronous versions found in
drivers/md/raid6recov.c.  The primary difference is breaking out the xor
operations into separate calls to async_xor.  Two helper routines are
introduced to perform scalar multiplication where needed.
async_sum_product() multiplies two sources by scalar coefficients and
then sums (xor) the result.  async_mult() simply multiplies a single
source by a scalar.

This implemention also includes, in contrast to the original
synchronous-only code, special case handling for the 4-disk and 5-disk
array cases.  In these situations the default N-disk algorithm will
present 0-source or 1-source operations to dma devices.  To cover for
dma devices where the minimum source count is 2 we implement 4-disk and
5-disk handling in the recovery code.

[ Impact: asynchronous raid6 recovery routines for 2data and datap cases ]

Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

[ Based on an original patch by Yuri Tikhonov ]

This adds support for doing asynchronous GF multiplication by adding
two additional functions to the async_tx API:

 async_gen_syndrome() does simultaneous XOR and Galois field
    multiplication of sources.

 async_syndrome_val() validates the given source buffers against known P
    and Q values.

When a request is made to run async_pq against more than the hardware
maximum number of supported sources we need to reuse the previous
generated P and Q values as sources into the next operation.  Care must
be taken to remove Q from P' and P from Q'.  For example to perform a 5
source pq op with hardware that only supports 4 sources at a time the
following approach is taken:

p, q = PQ(src0, src1, src2, src3, COEF({01}, {02}, {04}, {08}))
p', q' = PQ(p, q, q, src4, COEF({00}, {01}, {00}, {10}))

p' = p + q + q + src4 = p + src4
q' = {00}*p + {01}*q + {00}*q + {10}*src4 = q + {10}*src4

Note: 4 is the minimum acceptable maxpq otherwise we punt to
synchronous-software path.

The DMA_PREP_CONTINUE flag indicates to the driver to reuse p and q as
sources (in the above manner) and fill the remaining slots up to maxpq
with the new sources/coefficients.

Note1: Some devices have native support for P+Q continuation and can skip
this extra work.  Devices with this capability can advertise it with
dma_set_maxpq.  It is up to each driver how to handle the
DMA_PREP_CONTINUE flag.

Note2: The api supports disabling the generation of P when generating Q,
this is ignored by the synchronous path but is implemented by some dma
devices to save unnecessary writes.  In this case the continuation
algorithm is simplified to only reuse Q as a source.

Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

We currently walk the parent chain when waiting for a given tx to
complete however this walk may race with the driver cleanup routine.
The routines in async_raid6_recov.c may fall back to the synchronous
path at any point so we need to be prepared to call async_tx_quiesce()
(which calls  dma_wait_for_async_tx).  To remove the ->parent walk we
guarantee that every time a dependency is attached ->issue_pending() is
invoked, then we can simply poll the initial descriptor until
completion.

This also allows for a lighter weight 'issue pending' implementation as
there is no longer a requirement to iterate through all the channels'
->issue_pending() routines as long as operations have been submitted in
an ordered chain.  async_tx_issue_pending() is added for this case.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Replace the flat zero_sum_result with a collection of flags to contain
the P (xor) zero-sum result, and the soon to be utilized Q (raid6 reed
solomon syndrome) zero-sum result.  Use the SUM_CHECK_ namespace instead
of DMA_ since these flags will be used on non-dma-zero-sum enabled
platforms.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Prepare the api for the arrival of a new parameter, 'scribble'.  This
will allow callers to identify scratchpad memory for dma address or page
address conversions.  As this adds yet another parameter, take this
opportunity to convert the common submission parameters (flags,
dependency, callback, and callback argument) into an object that is
passed by reference.

Also, take this opportunity to fix up the kerneldoc and add notes about
the relevant ASYNC_TX_* flags for each routine.

[ Impact: moves api pass-by-value parameters to a pass-by-reference struct ]

Signed-off-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

In support of inter-channel chaining async_tx utilizes an ack flag to
gate whether a dependent operation can be chained to another.  While the
flag is not set the chain can be considered open for appending.  Setting
the ack flag closes the chain and flags the descriptor for garbage
collection.  The ASYNC_TX_DEP_ACK flag essentially means "close the
chain after adding this dependency".  Since each operation can only have
one child the api now implicitly sets the ack flag at dependency
submission time.  This removes an unnecessary management burden from
clients of the api.

[ Impact: clean up and enforce one dependency per operation ]

Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

'zero_sum' does not properly describe the operation of generating parity
and checking that it validates against an existing buffer.  Change the
name of the operation to 'val' (for 'validate').  This is in
anticipation of the p+q case where it is a requirement to identify the
target parity buffers separately from the source buffers, because the
target parity buffers will not have corresponding pq coefficients.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

To allow an async_tx routine to be compiled away on HAS_DMA=n arch it
needs to be declared __always_inline otherwise the compiler may emit
code and cause a link error.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>

async_tx and net_dma each have open-coded versions of issue_pending_all,
so provide a common routine in dmaengine.

The implementation needs to walk the global device list, so implement
rcu to allow dma_issue_pending_all to run lockless.  Clients protect
themselves from channel removal events by holding a dmaengine reference.

Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>