linux-toradex.git/include/linux/atmdev.h, branch Colibri_T30_LinuxImageV2.1Beta2_20140206

atomic: use

2011-07-26T23:49:47+00:00

This allows us to move duplicated code in 
(atomic_inc_not_zero() for now) to 

Signed-off-by: Arun Sharma 
Reviewed-by: Eric Dumazet 
Cc: Ingo Molnar 
Cc: David Miller 
Cc: Eric Dumazet 
Acked-by: Mike Frysinger 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

atm/solos-pci: Don't flap VCs when carrier state changes

2011-03-30T23:53:38+00:00

Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.

We no longer use release_vccs() so we can delete it.

release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.

Signed-off-by: Philip A. Prindeville 
Signed-off-by: David S. Miller

atm: correct sysfs 'device' link creation and parent relationships

2010-12-10T23:45:05+00:00

The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs.  This led to incorrect device/parent relationships
exposed by sysfs and udev.  Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.

Signed-off-by: Dan Williams 
Signed-off-by: David S. Miller

net: return operator cleanup

2010-09-23T21:33:39+00:00

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller

atm: propagate signal changes via notifier

2010-07-09T07:09:20+00:00

Add notifier chain for changes in atm_dev.

Clients like br2684 will call register_atmdevice_notifier() to be notified of
changes. Drivers will call atm_dev_signal_change() to notify clients like
br2684 of the change.

On DSL and ATM devices it's usefull to have a know if you have a carrier
signal. netdevice LOWER_UP changes can be propagated to userspace via netlink
monitor.

Signed-off-by: Karl Hiramoto 
Signed-off-by: David S. Miller

net: Make setsockopt() optlen be unsigned.

2009-09-30T23:12:20+00:00

This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.

Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.

Signed-off-by: David S. Miller

atm: 32-bit ioctl compatibility

2008-12-04T06:12:38+00:00

We lack compat ioctl support through most of the ATM code. This patch
deals with most of it, and I can now at least use BR2684 and PPPoATM
with 32-bit userspace.

I haven't added a .compat_ioctl method to struct atm_ioctl, because
AFAICT none of the current users need any conversion -- so we can just
call the ->ioctl() method in every case. I looked at br2684, clip, lec,
mpc, pppoatm and atmtcp.

In svc_compat_ioctl() the only mangling which is needed is to change
COMPAT_ATM_ADDPARTY to ATM_ADDPARTY. Although it's defined as
	_IOW('a', ATMIOC_SPECIAL+4,struct atm_iobuf)
it doesn't actually _take_ a struct atm_iobuf as an argument -- it takes
a struct sockaddr_atmsvc, which _is_ the same between 32-bit and 64-bit
code, so doesn't need conversion.

Almost all of vcc_ioctl() would have been identical, so I converted that
into a core do_vcc_ioctl() function with an 'int compat' argument.

I've done the same with atm_dev_ioctl(), where there _are_ a few
differences, but still it's relatively contained and there would
otherwise have been a lot of duplication.

I haven't done any of the actual device-specific ioctls, although I've
added a compat_ioctl method to struct atmdev_ops.

Signed-off-by: David Woodhouse 
Signed-off-by: David S. Miller

[ATM]: Convert struct class_device to struct device

2008-01-28T23:00:12+00:00

Signed-off-by: Kay Sievers 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Chas Williams

[PATCH] Move linux/device.h include in linux/atmdev.h to #ifdef KERNEL section

2006-09-06T18:00:02+00:00

linux/device.h header is not included in the David Woodhouse's
kernel-headers git tree which is used for userspace kernel headers.  Which
results in compile errors when building iproute2.  Attached patch moves
linux/device.h include under the #ifdef __KERNEL__ section.

Signed-off-by: Ismail Donmez 
Signed-off-by: David Woodhouse 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

[ATM]: basic sysfs support for ATM devices

2006-06-29T23:58:19+00:00

Signed-off-by: Chas Williams 
Signed-off-by: David S. Miller