Pull sound updates from Takashi Iwai:
 "This contains pretty many small commits covering fairly large range of
  files in sound/ directory.  Partly because of additional API support
  and partly because of constantly developed ASoC and ARM stuff.

  Some highlights:

   - Introduced the helper function and documentation for exposing the
     channel map via control API, as discussed in Plumbers; most of PCI
     drivers are covered, will follow more drivers later

   - Most of drivers have been replaced with the new PM callbacks (if
     the bus is supported)

   - HD-audio controller got the support of runtime PM and the support
     of D3 clock-stop.  Also changing the power_save option in sysfs
     kicks off immediately to enable / disable the power-save mode.

   - Another significant code change in HD-audio is the rewrite of
     firmware loading code.  Other than that, most of changes in
     HD-audio are continued cleanups and standardization for the generic
     auto parser and bug fixes (HBR, device-specific fixups), in
     addition to the support of channel-map API.

   - Addition of ASoC bindings for the compressed API, used by the
     mid-x86 drivers.

   - Lots of cleanups and API refreshes for ASoC codec drivers and
     DaVinci.

   - Conversion of OMAP to dmaengine.

   - New machine driver for Wolfson Microelectronics Bells.

   - New CODEC driver for Wolfson Microelectronics WM0010.

   - Enhancements to the ux500 and wm2000 drivers

   - A new driver for DA9055 and the support for regulator bypass mode."

Fix up various arm soc header file reorg conflicts.

* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
  ALSA: hda - Add new codec ALC283 ALC290 support
  ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
  ALSA: hda - fix indices on boost volume on Conexant
  ALSA: aloop - add locking to timer access
  ALSA: hda - Fix hang caused by race during suspend.
  sound: Remove unnecessary semicolon
  ALSA: hda/realtek - Fix detection of ALC271X codec
  ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
  ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
  ALSA: hda - make a generic unsol event handler
  ASoC: codecs: Add DA9055 codec driver
  ASoC: eukrea-tlv320: Convert it to platform driver
  ALSA: ASoC: add DT bindings for CS4271
  ASoC: wm_hubs: Ensure volume updates are handled during class W startup
  ASoC: wm5110: Adding missing volume update bits
  ASoC: wm5110: Add OUT3R support
  ASoC: wm5110: Add AEC loopback support
  ASoC: wm5110: Rename EPOUT to HPOUT3
  ASoC: arizona: Add more clock rates
  ASoC: arizona: Add more DSP options for mixer input muxes
  ...

Pull MFD changes from Samuel Ortiz:
 "MFD bits for the 3.7 merge window.

  As usual we have a few new drivers:

   - TI LP8788
   - TI OMAP USB TLL
   - Maxim MAX8907
   - SMSC ECE1099
   - Dialog Semiconductor DA9055
   - A simpler syscon driver that allow us to get rid of the anatop one.

  Drivers are also gradually getting Device Tree and IRQ domain support.

  The following drivers got DT support:
   - palmas, 88pm860x, tc3589x and twl4030-audio

  And those ones now use the IRQ domain APIs:
   - 88pm860x, tc3589x, db8500_prcmu

  Also some other interesting changes:
   - Intel's ICH LPC now supports Lynx Point
   - TI's twl4030-audio added a GPO child
   - tps6527 enabled its backlight subdevice
   - The twl6030 pwm driver moved to the new PWM subsystem

  And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
  palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."

Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.

Guys, DON'T REBASE!

* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
  ARM: dts: Enable 88pm860x pmic
  mfd: 88pm860x: Move gpadc init into touch
  mfd: 88pm860x: Device tree support
  mfd: 88pm860x: Use irqdomain
  mfd: smsc: Add support for smsc gpio io/keypad driver
  backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
  mfd: DA9055 core driver
  mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
  mfd: wm5110: Add register patches for revision B
  mfd: wm5110: Disable control interface error report for WM5110 rev B
  mfd: max8907: Remove regulator-compatible from DT docs
  backlight: Add TPS65217 WLED driver
  mfd: Add backlight as subdevice to the tps65217
  mfd: Provide the PRCMU with its own IRQ domain
  mfd: Fix max8907 sparse warning
  mfd: Add lp8788 mfd driver
  mfd: dbx500: Provide a more accurate smp_twd clock
  mfd: rc5t583: Fix warning messages
  regulator: palmas: Add DT support
  mfd: palmas: Change regulator defns to better suite DT
  ...

We no longer have users for the set_hs_extmute callback which has been
replaced by hs_extmute_gpio so the codec driver can handle the external
mute if it is needed by the board.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The external mute (if it is in use) is handled by a GPIO line. Prepare to
remove the set_hs_extmute callback and replace it with:
hs_extmute_gpio: the GPIO number to use for external mute

When the users of set_hs_extmute has been converted the callback can be removed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We can't use hardcoded interrupts for SPARSE_IRQ, and can replace
the hardcoded gpio_base with twl_gpiochip.base after it's been
allocated.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull battery updates from Anton Vorontsov:
 "The tag contains just a few battery-related changes for v3.6.  It's is
  all pretty straightforward, except one thing.

  One of our patches added thermal support for power supply class, but
  thermal/ subsystem changed under our feet.  We (well, Stephen, that
  is) caught the issue and it was decided[1] that I'd just delay the
  battery pull request, and then will fix it up by merging upstream back
  into battery tree at the specific commit.

  That's not all though: another[2] small fixup for thermal subsystem
  was needed to get rid of a warning in power supply subsystem (the
  warning was not drivers/power's "fault", the thermal registration
  function just needed a proper const annotation, which is also done by
  a small commit on top of the merge.

  So, to sum this up:
   - The 'master' branch of the battery tree was in the -next tree for
     weeks, was never rebased, altered etc.  It should be all OK;
   - Although, for-v3.6 tag contains the 'master' branch + merge + the
     warning fix.

  [1] http://lkml.org/lkml/2012/6/19/23
  [2] http://lkml.org/lkml/2012/6/18/28"

* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
  thermal: Constify 'type' argument for the registration routine
  olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
  olpc-battery: Add VOLTAGE_MAX_DESIGN property
  charger-manager: Fix build break related to EXTCON
  lp8727_charger: Move header file into platform_data directory
  power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
  bq27x00_battery: Add support for BQ27425 chip
  charger-manager: Set current limit of regulator for over current protection
  charger-manager: Use EXTCON Subsystem to detect charger cables for charging
  test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
  test_power: Add support for USB AC source
  gpio-charger: Use cansleep version of gpio_set_value
  bq27x00_battery: Add support for power average and health properties
  sbs-battery: Don't trigger false supply_changed event
  twl4030_charger: Allow charger to control the regulator that feeds it
  twl4030_charger: Add backup-battery charging
  twl4030_charger: Fix some typos
  max17042_battery: Support CHARGE_COUNTER power supply attribute
  smb347-charger: Add constant charge and current properties
  power_supply: Add constant charge_current and charge_voltage properties
  ...

This allows a voltage and current (bb_uvolts and bb_uamps) to be
specified in the platform_data, and charging of the backup battery will
be enabled with those specification.

As it is not possible to monitor the backup battery at all there is no
new device created to represent it.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

After converstion to SPARSE_IRQ, the driver doesn't use the
pdata->irq_base/irq_end fields anymore.  The last users
have been cleanup up, and now these fields can be removed.

Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>