linux-toradex.git/include/linux/ieee80211.h, branch T30_LinuxImageV2.0Beta2_20130626

ieee80211: add few wmm tspec values

2011-07-19T20:49:54+00:00

These are needed by ath6kl for parsing tspec status from an IE.

Signed-off-by: Kalle Valo 
Signed-off-by: John W. Linville

wireless: unify QoS control field definitions

2011-06-27T19:09:39+00:00

Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.

Signed-off-by: Johannes Berg 
Signed-off-by: John W. Linville

cfg80211: don't drop p2p probe responses

2011-06-01T18:34:01+00:00

Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.

However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.

Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.

Signed-off-by: Eliad Peller 
Signed-off-by: John W. Linville

mac80211: Self-protected management frames are not robust

2011-05-11T18:44:48+00:00

They may contain encrypted information elements (as AMPE frames do)
but they are not encrypted.

Signed-off-by: Thomas Pedersen 
Signed-off-by: Javier Cardona 
Signed-off-by: John W. Linville

cfg80211: Use capability info to detect mesh beacons.

2011-05-11T18:37:48+00:00

Mesh beacons no longer use all-zeroes BSSID.  Beacon frames for MBSS,
infrastructure BSS, or IBSS are differentiated by the Capability
Information field in the Beacon frame.  A mesh STA sets the ESS and IBSS
subfields to 0 in transmitted Beacon or Probe Response management
frames.

Signed-off-by: Javier Cardona 
Signed-off-by: John W. Linville

mac80211: Drop MESH_PLINK category and use new ANA-approved MESH_ACTION

2011-05-11T18:37:47+00:00

Note: This breaks compatibility with previous mesh protocol instances.

Signed-off-by: Javier Cardona 
Signed-off-by: John W. Linville

ieee80211: add HT extended capabilities masks

2011-04-04T20:20:05+00:00

IEEE Std 802.11n, Oct. 29, 2009:
7.3.2.56.5 HT Extended Capabilities field

Signed-off-by: Bing Zhao 
Signed-off-by: John W. Linville

ieee80211: add IEEE80211_COUNTRY_STRING_LEN definition

2011-03-09T21:10:56+00:00

and make use of it in wireless drivers

Signed-off-by: Bing Zhao 
Signed-off-by: John W. Linville

ieee80211: correct IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK macro

2011-01-13T20:46:45+00:00

It is defined in include/linux/ieee80211.h. As per IEEE spec.
bit6 to bit15 in block ack parameter represents buffer size.
So the bitmask should be 0xFFC0.

Signed-off-by: Amitkumar Karwar 
Signed-off-by: Bing Zhao 
Cc: stable@kernel.org
Reviewed-by: Johannes Berg 
Signed-off-by: John W. Linville

mac80211: Remove unused third address from mesh address extension header.

2010-12-20T19:49:47+00:00

The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4.  If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).

The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft.  See
section 7.1.3.6.3 in current draft (8.0).

Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats.  But I thought I better
remove it before someone does start using it.

Signed-off-by: Javier Cardona 
Signed-off-by: John W. Linville