linux-toradex.git/include/linux/ipv6.h, branch v4.6-rc3

net: ipv6: Make address flushing on ifdown optional

2016-02-26T02:45:15+00:00

Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:

    $ ip -6 addr show dev eth1
    3: eth1:  mtu 1500 state UP qlen 1000
        inet6 2100:1::2/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
           valid_lft forever preferred_lft forever
    $ ip link set dev eth1 down
    $ ip -6 addr show dev eth1
    << nothing; all addresses have been flushed>>

Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces

    $ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
    $ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1

Will keep addresses on eth1 on an admin down.

    $ ip -6 addr show dev eth1
    3: eth1:  mtu 1500 state UP qlen 1000
        inet6 2100:1::2/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
           valid_lft forever preferred_lft forever
    $ ip link set dev eth1 down
    $ ip -6 addr show dev eth1
    3: eth1:  mtu 1500 state DOWN qlen 1000
        inet6 2100:1::2/120 scope global tentative
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
           valid_lft forever preferred_lft forever

Signed-off-by: David Ahern 
Signed-off-by: David S. Miller

ipv6: add option to drop unsolicited neighbor advertisements

2016-02-11T09:27:36+00:00

In certain 802.11 wireless deployments, there will be NA proxies
that use knowledge of the network to correctly answer requests.
To prevent unsolicitd advertisements on the shared medium from
being a problem, on such deployments wireless needs to drop them.

Enable this by providing an option called "drop_unsolicited_na".

Signed-off-by: Johannes Berg 
Signed-off-by: David S. Miller

ipv6: add option to drop unicast encapsulated in L2 multicast

2016-02-11T09:27:36+00:00

In order to solve a problem with 802.11, the so-called hole-196 attack,
add an option (sysctl) called "drop_unicast_in_l2_multicast" which, if
enabled, causes the stack to drop IPv6 unicast packets encapsulated in
link-layer multi- or broadcast frames. Such frames can (as an attack)
be created by any member of the same wireless network and transmitted
as valid encrypted frames since the symmetric key for broadcast frames
is shared between all stations.

Reviewed-by: Julian Anastasov 
Signed-off-by: Johannes Berg 
Signed-off-by: David S. Miller

ipv6: add complete rcu protection around np->opt

2015-12-03T04:37:16+00:00

This patch addresses multiple problems :

UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.

Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())

This patch adds full RCU protection to np->opt

Reported-by: Dmitry Vyukov 
Signed-off-by: Eric Dumazet 
Acked-by: Hannes Frederic Sowa 
Signed-off-by: David S. Miller

ipv6: inet6_sk() should use sk_fullsock()

2015-10-05T09:45:25+00:00

SYN_RECV & TIMEWAIT sockets are not full blown, they do not have a pinet6
pointer.

Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller

net: ipv6 sysctl option to ignore routes when nexthop link is down

2015-08-14T04:27:19+00:00

Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link.  The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:

net.ipv6.conf.all.ignore_routes_with_linkdown = 0
net.ipv6.conf.default.ignore_routes_with_linkdown = 0
net.ipv6.conf.lo.ignore_routes_with_linkdown = 0
...

When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.

1000::/8 via 7000::2 dev p7p1  metric 1024 dead linkdown  pref medium
1000::/8 via 8000::2 dev p8p1  metric 1024  pref medium
7000::/8 dev p7p1  proto kernel  metric 256 dead linkdown  pref medium
8000::/8 dev p8p1  proto kernel  metric 256  pref medium
9000::/8 via 8000::2 dev p8p1  metric 2048  pref medium
9000::/8 via 7000::2 dev p7p1  metric 1024 dead linkdown  pref medium
fe80::/64 dev p7p1  proto kernel  metric 256 dead linkdown  pref medium
fe80::/64 dev p8p1  proto kernel  metric 256  pref medium

This also adds devconf support and notification when sysctl values
change.

v2: drop use of rt6i_nhflags since it is not needed right now

Signed-off-by: Andy Gospodarek 
Signed-off-by: Dinesh Dutt 
Signed-off-by: David S. Miller

net/ipv6: add sysctl option accept_ra_min_hop_limit

2015-07-30T22:56:40+00:00

Commit 6fd99094de2b ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.

RFC 4861, 6.3.4.  Processing Received Router Advertisements
   A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
   and Retrans Timer) may contain a value denoting that it is
   unspecified.  In such cases, the parameter should be ignored and the
   host should continue using whatever value it is already using.

   If the received Cur Hop Limit value is non-zero, the host SHOULD set
   its CurHopLimit variable to the received value.

So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.

Signed-off-by: Hangbin Liu 
Acked-by: YOSHIFUJI Hideaki 
Signed-off-by: David S. Miller

ipv6: sysctl to restrict candidate source addresses

2015-07-22T17:54:11+00:00

Per RFC 6724, section 4, "Candidate Source Addresses":

    It is RECOMMENDED that the candidate source addresses be the set
    of unicast addresses assigned to the interface that will be used
    to send to the destination (the "outgoing" interface).

Add a sysctl to enable this behaviour.

Signed-off-by: Erik Kline 
Signed-off-by: David S. Miller

ipv6: use flag instead of u16 for hop in inet6_skb_parm

2015-07-09T22:06:59+00:00

Hop was always either 0 or sizeof(struct ipv6hdr).

Signed-off-by: Florian Westphal 
Signed-off-by: David S. Miller

ipv6: introduce secret_stable to ipv6_devconf

2015-03-24T02:12:08+00:00

This patch implements the procfs logic for the stable_address knob:
The secret is formatted as an ipv6 address and will be stored per
interface and per namespace. We track initialized flag and return EIO
errors until the secret is set.

We don't inherit the secret to newly created namespaces.

Cc: Erik Kline 
Cc: Fernando Gont 
Cc: Lorenzo Colitti 
Cc: YOSHIFUJI Hideaki/吉藤英明 
Signed-off-by: Hannes Frederic Sowa 
Signed-off-by: David S. Miller