* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  irq: Track the owner of irq descriptor
  irq: Always set IRQF_ONESHOT if no primary handler is specified
  genirq: Fix wrong bit operation

Interrupt descriptors can be allocated from modules. The interrupts
are used by other modules, but we have no refcount on the module which
provides the interrupts and there is no way to establish one on the
device level as the interrupt using module is agnostic to the fact
that the interrupt is provided by a module rather than by some builtin
interrupt controller.

To prevent removal of the interrupt providing module, we can track the
owner of the interrupt descriptor, which also provides the relevant
irq chip functions in the irq descriptor.

request/setup_irq() can now acquire a refcount on the owner module to
prevent unloading. free_irq() drops the refcount.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/20110711101731.GA13804@Chamillionaire.breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs.  This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller.  irq_domain
supports device tree translation for any number of interrupt
controllers.

This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation.  x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet.  On ARM it works and is required for much of the new
ARM device tree board support.

PowerPC has /not/ been converted to use this new infrastructure.  It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details).  Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.

SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.

Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  um: Make rwsem.S depend on CONFIG_RWSEM_XCHGADD_ALGORITHM

* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  debug: Make CONFIG_EXPERT select CONFIG_DEBUG_KERNEL to unhide debug options

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Remove unused CHECK_IRQ_PER_CPU()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools, x86: Fix 32-bit compile on 64-bit system

This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".

Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.

Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().

For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.

Tested on Network Space v2.

Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

No more users. Kill it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

These callbacks are only called in the syscore suspend/resume code on
interrupt chips which have been registered via the generic irq chip
mechanism. Calling those callbacks per irq would be rather icky, but
with the generic irq chip mechanism we can call this per registered
chip.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org

Implement a generic interrupt chip, which is configurable and is able
to handle the most common irq chip implementations.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by; Kevin Hilman <khilman@ti.com>

This adds support for disabling threading on a per-IRQ basis via the IRQ
status instead of the IRQ flow, which is necessary for interrupts that
don't follow the natural IRQ flow channels, such as those that are
virtually created.

The new APIs added are simply:

	irq_set_thread()
	irq_set_nothread()

which follow the rest of the IRQ status routines.

Chained handlers also have IRQ_NOTHREAD set on them automatically, making
the lack of threading explicit rather than implicit. Subsequently, the
nothread flag can be viewed through the standard genirq debugging
facilities.

[ tglx: Fixed cleanup fallout ]

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/%3C20110406210135.GF18426%40linux-sh.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

commit 0c6f8a8b917ad361319c8ace3e9f28e69bfdb4c1 ("genirq: Remove compat code")
removed the compat code, but forgot to update some references in comments and
delete some of its documentation.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/%3C1302426113-13808-1-git-send-email-geert%40linux-m68k.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>