linux-toradex.git/include/linux/libata.h, branch v2.6.35-rc3

libata: implement on-demand HPA unlocking

2010-06-02T17:50:10+00:00

Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device.  It requests EH to unlock
HPA, waits for completion and returns the current device capacity.

This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront.  Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit.  This was suggested by Ben Hutchings.

Signed-off-by: Tejun Heo 
Suggested-by: Ben Hutchings 
Signed-off-by: Jeff Garzik

libata: implement dump_id force param

2010-05-25T23:41:19+00:00

Add dump_id libata.force parameter.  If specified, libata dumps full
IDENTIFY data during device configuration.  This is to aid debugging.

Signed-off-by: Tejun Heo 
Cc: Larry Baker 
Signed-off-by: Jeff Garzik

libata-sff: make BMDMA optional

2010-05-25T23:41:12+00:00

Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones.  Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.

ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.

This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced.  Either way, the size difference is insignificant.  This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA init

2010-05-25T23:40:30+00:00

Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts.  SFF ones no longer try to initialize
BMDMA or set PCI master.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA irq handler

2010-05-25T23:40:24+00:00

Separate out BMDMA irq handler from SFF irq handler.  The misnamed
host_intr() functions are renamed to ata_sff_port_intr() and
ata_bmdma_port_intr().  Common parts are factored into
__ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and
bmdma interrupt routines.

All BMDMA drivers now use ata_bmdma_interrupt() or
ata_bmdma_port_intr() while all non-BMDMA SFF ones use
ata_sff_interrupt() or ata_sff_port_intr().

For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's
used by both SFF and BMDMA drivers.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: ata_sff_irq_clear() is BMDMA specific

2010-05-25T23:40:19+00:00

ata_sff_irq_clear() is BMDMA specific.  Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.

Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
      possibly by sata_sil.  This should be moved to respective low
      level drivers later.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA qc_issue

2010-05-19T17:38:55+00:00

Separate out ata_bmdma_qc_issue() from ata_sff_qc_issue() such that
ata_sff_qc_issue() only deals with non-BMDMA SFF protocols (PIO and
nodata) while ata_bmdma_qc_issue() deals with the BMDMA protocols and
uses ata_sff_qc_issue() for non-DMA commands.  All the users are
updated accordingly.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: prd is BMDMA specific

2010-05-19T17:38:54+00:00

struct ata_prd and ap->prd are BMDMA specific.  Add bmdma_ prefix to
them and move them inside CONFIG_ATA_SFF.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: ata_sff_[dumb_]qc_prep are BMDMA specific

2010-05-19T17:36:50+00:00

Both qc_prep functions deal only with BMDMA PRD setup and PIO only SFF
drivers don't need them.  Rename to ata_bmdma_[dumb_]qc_prep() and
relocate.

All usages are renamed except for pdc_adma and sata_qstor.  Those two
drivers are not BMDMA drivers and don't need to call BMDMA qc_prep
functions.  Calls to ata_sff_qc_prep() in the two drivers are removed.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA EH

2010-05-19T17:36:46+00:00

Some of error handling logic in ata_sff_error_handler() and all of
ata_sff_post_internal_cmd() are for BMDMA.  Create
ata_bmdma_error_handler() and ata_bmdma_post_internal_cmd() and move
BMDMA part into those.

While at it, change DMA protocol check to ata_is_dma(), fix
post_internal_cmd to call ap->ops->bmdma_stop instead of directly
calling ata_bmdma_stop() and open code hardreset selection so that
ata_std_error_handler() doesn't have to know about sff hardreset.

As these two functions are BMDMA specific, there's no reason to check
for bmdma_addr before calling bmdma methods if the protocol of the
failed command is DMA.  sata_mv and pata_mpc52xx now don't need to set
.post_internal_cmd to ATA_OP_NULL and pata_icside and sata_qstor don't
need to set it to their bmdma_stop routines.

ata_sff_post_internal_cmd() becomes noop and is removed.

This fixes p3 described in clean-up-BMDMA-initialization patch.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik