linux-toradex.git/include/linux/libata.h, branch v6.16-rc6

ata: libata-acpi: Do not assume 40 wire cable if no devices are enabled

2025-06-10T12:08:24+00:00

On at least an ASRock 990FX Extreme 4 with a VIA VT6330, the devices
have not yet been enabled by the first time ata_acpi_cbl_80wire() is
called. This means that the ata_for_each_dev loop is never entered,
and a 40 wire cable is assumed.

The VIA controller on this board does not report the cable in the PCI
config space, thus having to fall back to ACPI even though no SATA
bridge is present.

The _GTM values are correctly reported by the firmware through ACPI,
which has already set up faster transfer modes, but due to the above
the controller is forced down to a maximum of UDMA/33.

Resolve this by modifying ata_acpi_cbl_80wire() to directly return the
cable type. First, an unknown cable is assumed which preserves the mode
set by the firmware, and then on subsequent calls when the devices have
been enabled, an 80 wire cable is correctly detected.

Since the function now directly returns the cable type, it is renamed
to ata_acpi_cbl_pata_type().

Signed-off-by: Tasos Sahanidis 
Link: https://lore.kernel.org/r/20250519085945.1399466-1-tasos@tasossah.com
Signed-off-by: Niklas Cassel

ata: libata: Print if port is external on boot

2025-05-14T07:12:39+00:00

Commit affccb16c117 ("ata: ahci: print the lpm policy on boot") added a
lpm-pol print during boot, which shows the LPM policy used by each port.

While the LPM policy is usually determined by the Kconfig
CONFIG_SATA_MOBILE_LPM_POLICY, the Kconfig value is overridden e.g. if
firmware has marked the port as hotplug capable / external.

Commit f97106b10d9a ("ata: ahci: Add debug print for external port") did
add a debug print to show if LPM was disabled because firmware has marked
the port as external, however, because devices having broken LPM (even
though they claim to support it) is more common than one would have hoped,
print "ext" during boot if firmware has marked the port is external.

This will make it easier to debug certain LPM issues, e.g. if firmware has
enabled/marked only some of the ports as hotplug capable / external.

Before (port marked as external by firmware):
ata1: SATA max UDMA/133 abar m4096@0xfebd3000 port 0xfebd3100 irq 57 lpm-pol 0

After (port marked as external by firmware):
ata1: SATA max UDMA/133 abar m4096@0xfebd3000 port 0xfebd3100 irq 57 lpm-pol 0 ext

Signed-off-by: Niklas Cassel 
Signed-off-by: Damien Le Moal

ata: libata-core: Simplify ata_print_version_once

2025-04-20T23:52:48+00:00

Use dev_dbg_once() instead of open-coding the once functionality.

Signed-off-by: Heiner Kallweit 
Signed-off-by: Damien Le Moal

Merge tag 'ata-6.14-final' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux

2025-03-19T14:31:43+00:00

Pull ata fix from Niklas Cassel:

 - Fix a regression on ATI AHCI controllers, where certain Samsung
   drives fails to be detected on a warm boot when LPM is enabled.

   LPM on ATI AHCI works fine with other drives. Likewise, the
   Samsung drives works fine with LPM with other AHI controllers.

   Thus, just like the weirdo ATA_QUIRK_NO_NCQ_ON_ATI quirk, add a
   new ATA_QUIRK_NO_LPM_ON_ATI quirk to disable LPM only on ATI
   AHCI controllers.

* tag 'ata-6.14-final' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
  ata: libata-core: Add ATA_QUIRK_NO_LPM_ON_ATI for certain Samsung SSDs

ata: libata-core: Add ATA_QUIRK_NO_LPM_ON_ATI for certain Samsung SSDs

2025-03-18T09:11:28+00:00

Before commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
the ATI AHCI controllers specified board type 'board_ahci' rather than
board type 'board_ahci'. This means that LPM was historically not enabled
for the ATI AHCI controllers.

By looking at commit 7a8526a5cd51 ("libata: Add ATA_HORKAGE_NO_NCQ_ON_ATI
for Samsung 860 and 870 SSD."), it is clear that, for some unknown reason,
that Samsung SSDs do not play nice with ATI AHCI controllers. (When using
other AHCI controllers, NCQ can be enabled on these Samsung SSDs without
issues.)

In a similar way, from user reports, it is clear the ATI AHCI controllers
can enable LPM on e.g. Maxtor HDDs perfectly fine, but when enabling LPM
on certain Samsung SSDs, things break. (E.g. the SSDs will not get detected
by the ATI AHCI controller even after a COMRESET.)

Yet, when using LPM on these Samsung SSDs with other AHCI controllers, e.g.
Intel AHCI controllers, these Samsung drives appear to work perfectly fine.

Considering that the combination of ATI + Samsung, for some unknown reason,
does not seem to work well, disable LPM when detecting an ATI AHCI
controller with a problematic Samsung SSD.

Apply this new ATA_QUIRK_NO_LPM_ON_ATI quirk for all Samsung SSDs that have
already been reported to not play nice with ATI (ATA_QUIRK_NO_NCQ_ON_ATI).

Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Suggested-by: Hans de Goede 
Reported-by: Eric 
Closes: https://lore.kernel.org/linux-ide/Z8SBZMBjvVXA7OAK@eldamar.lan/
Tested-by: Eric 
Reviewed-by: Damien Le Moal 
Link: https://lore.kernel.org/r/20250317170348.1748671-2-cassel@kernel.org
Signed-off-by: Niklas Cassel

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2025-01-27T00:12:44+00:00

Pull SCSI updates from James Bottomley:
 "Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).

  The major core change is the renaming of the slave_ methods plus a bit
  of constification. The rest are minor updates and fixes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
  scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
  scsi: fnic: Test for memory allocation failure and return error code
  scsi: fnic: Return appropriate error code from failure of scsi drv init
  scsi: fnic: Return appropriate error code for mem alloc failure
  scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
  scsi: fnic: Fix use of uninitialized value in debug message
  scsi: fnic: Delete incorrect debugfs error handling
  scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
  scsi: fnic: Remove extern definition from .c files
  scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
  scsi: mpi3mr: Fix possible crash when setting up bsg fails
  scsi: ufs: bsg: Set bsg_queue to NULL after removal
  scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
  scsi: st: Don't set pos_unknown just after device recognition
  scsi: aic7xxx: Fix build 'aicasm' warning
  scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
  scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
  scsi: scsi_debug: Constify sdebug_driver_template
  scsi: documentation: Corrections for struct updates
  scsi: driver-api: documentation: Change what is added to docbook
  ...

block: simplify tag allocation policy selection

2025-01-06T14:37:41+00:00

Use a plain BLK_MQ_F_* flag to select the round robin tag selection
instead of overlaying an enum with just two possible values into the
flags space.

Doing so allows adding a BLK_MQ_F_MAX sentinel for simplified overflow
checking in the messy debugfs helpers.

Signed-off-by: Christoph Hellwig 
Reviewed-by: John Garry 
Link: https://lore.kernel.org/r/20250106083531.799976-5-hch@lst.de
Signed-off-by: Jens Axboe

scsi: Rename .device_configure() into .sdev_configure()

2024-12-04T20:34:28+00:00

Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().

Cc: Christoph Hellwig 
Acked-by: Damien Le Moal 
Signed-off-by: Bart Van Assche 
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen

scsi: Rename .slave_alloc() and .slave_destroy()

2024-12-04T20:34:28+00:00

Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.

This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
  except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
  files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
  alignment (dc395x driver and include/linux/libata.h).

Acked-by: Damien Le Moal 
Signed-off-by: Bart Van Assche 
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen

ata: libata: Remove unused macro definitions

2024-10-09T08:26:27+00:00

ATA_TMOUT_BOOT and ATA_TMOUT_BOOT_QUICK are not used anywhere. Delete
these definitions.

Signed-off-by: Damien Le Moal 
Link: https://lore.kernel.org/r/20241009081535.376994-1-dlemoal@kernel.org
Signed-off-by: Niklas Cassel