linux-toradex.git/include/linux/mlx4/cmd.h, branch v3.17-rc4

mlx4_core: Add support for secure-host and SMP firewall

2014-08-05T14:40:22+00:00

Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.

This is achieved by:
1. Not allowing un-trusted entities to access device configuration
   registers, directly (through pci_cr or pci_conf) and indirectly
   (through MADs).

2. Hiding M_Key from untrusted entities.

3. Preventing the modification of GUID0 by un-trusted entities

4. Not allowing drivers on untrusted hosts to receive nor to transmit
   packets over QP0 (SMP Firewall).

The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.

Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.

Signed-off-by: Jack Morgenstein 
Signed-off-by: Or Gerlitz 

[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]

Signed-off-by: Roland Dreier

mlx4: Add support for CONFIG_DEV command

2014-03-28T20:29:35+00:00

Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.

Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

mlx4: Implement IP based gids support for RoCE/SRIOV

2014-03-12T19:57:16+00:00

Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.

Signed-off-by: Moni Shoua 
Signed-off-by: Jack Morgenstein 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2014-01-25T19:17:34+00:00

Pull networking updates from David Miller:

 1) BPF debugger and asm tool by Daniel Borkmann.

 2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.

 3) Correct reciprocal_divide and update users, from Hannes Frederic
    Sowa and Daniel Borkmann.

 4) Currently we only have a "set" operation for the hw timestamp socket
    ioctl, add a "get" operation to match.  From Ben Hutchings.

 5) Add better trace events for debugging driver datapath problems, also
    from Ben Hutchings.

 6) Implement auto corking in TCP, from Eric Dumazet.  Basically, if we
    have a small send and a previous packet is already in the qdisc or
    device queue, defer until TX completion or we get more data.

 7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.

 8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
    Borkmann.

 9) Share IP header compression code between Bluetooth and IEEE802154
    layers, from Jukka Rissanen.

10) Fix ipv6 router reachability probing, from Jiri Benc.

11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.

12) Support tunneling in GRO layer, from Jerry Chu.

13) Allow bonding to be configured fully using netlink, from Scott
    Feldman.

14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
    already get the TCI.  From Atzm Watanabe.

15) New "Heavy Hitter" qdisc, from Terry Lam.

16) Significantly improve the IPSEC support in pktgen, from Fan Du.

17) Allow ipv4 tunnels to cache routes, just like sockets.  From Tom
    Herbert.

18) Add Proportional Integral Enhanced packet scheduler, from Vijay
    Subramanian.

19) Allow openvswitch to mmap'd netlink, from Thomas Graf.

20) Key TCP metrics blobs also by source address, not just destination
    address.  From Christoph Paasch.

21) Support 10G in generic phylib.  From Andy Fleming.

22) Try to short-circuit GRO flow compares using device provided RX
    hash, if provided.  From Tom Herbert.

The wireless and netfilter folks have been busy little bees too.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
  net/cxgb4: Fix referencing freed adapter
  ipv6: reallocate addrconf router for ipv6 address when lo device up
  fib_frontend: fix possible NULL pointer dereference
  rtnetlink: remove IFLA_BOND_SLAVE definition
  rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
  qlcnic: update version to 5.3.55
  qlcnic: Enhance logic to calculate msix vectors.
  qlcnic: Refactor interrupt coalescing code for all adapters.
  qlcnic: Update poll controller code path
  qlcnic: Interrupt code cleanup
  qlcnic: Enhance Tx timeout debugging.
  qlcnic: Use bool for rx_mac_learn.
  bonding: fix u64 division
  rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
  sfc: Use the correct maximum TX DMA ring size for SFC9100
  Add Shradha Shah as the sfc driver maintainer.
  net/vxlan: Share RX skb de-marking and checksum checks with ovs
  tulip: cleanup by using ARRAY_SIZE()
  ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
  net/cxgb4: Don't retrieve stats during recovery
  ...

mlx4_core: Add support for steerable IB UD QPs

2014-01-14T22:06:50+00:00

This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.

Signed-off-by: Matan Barak 
Signed-off-by: Or Gerlitz 
Signed-off-by: Roland Dreier

net/mlx4_core: Add basic support for TCP/IP offloads under tunneling

2013-12-31T19:31:43+00:00

Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions

Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Fix typo, move similar defs to same location

2013-10-17T19:10:50+00:00

Small code cleanup:

1. change MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN to MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN

2. put MLX4_SET_PORT_PRIO2TC and MLX4_SET_PORT_SCHEDULER in the same union with the
   other MLX4_SET_PORT_yyy

Signed-off-by: Or Gerlitz 
Signed-off-by: Amir Vadai 
Signed-off-by: David S. Miller

net/mlx4_core: Respond to operation request by firmware

2013-07-29T08:12:40+00:00

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.

Signed-off-by: Yevgeny Petrilin 
Signed-off-by: Jack Morgenstein 
Signed-off-by: Eugenia Emantayev 
Signed-off-by: Amir Vadai 
Signed-off-by: David S. Miller

net/mlx4_core: Dynamic VST to VST vlan/qos changes

2013-07-01T20:10:22+00:00

Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.

This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).

To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.

If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.

Signed-off-by: Jack Morgenstein 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add VF link state support

2013-06-14T00:51:04+00:00

Add support to change the link state of VF (vPort)

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller