The newest device firmware stores IB vs. Ethernet protocol in two bits
in members_count field of multicast group table (0: Infiniband, 1:
Ethernet).  When changing the QP members count for a multicast group,
it important not to reset this information.  When calling multicast
attach first time, the protocol type should be specified.  In this
patch we always set it IB, but in the future we will handle Ethernet
too.  When looking for a QP, the protocol type shoud be checked too.

Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
  IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
  IB/qib: Allow driver to load if PCIe AER fails
  IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
  IB/qib: Fix extra log level in qib_early_err()
  RDMA/cxgb4: Remove unnecessary KERN_<level> use
  RDMA/cxgb3: Remove unnecessary KERN_<level> use
  IB/core: Add link layer type information to sysfs
  IB/mlx4: Add VLAN support for IBoE
  IB/core: Add VLAN support for IBoE
  IB/mlx4: Add support for IBoE
  mlx4_en: Change multicast promiscuous mode to support IBoE
  mlx4_core: Update data structures and constants for IBoE
  mlx4_core: Allow protocol drivers to find corresponding interfaces
  IB/uverbs: Return link layer type to userspace for query port operation
  IB/srp: Sync buffer before posting send
  IB/srp: Use list_first_entry()
  IB/srp: Reduce number of BUSY conditions
  IB/srp: Eliminate two forward declarations
  IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
  IB: Replace EXTRA_CFLAGS with ccflags-y
  ...

This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames.  The VLAN tag is encoded in the GID and derived from it
by a simple computation.

The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add support for IBoE to mlx4_ib.  The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs).  Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.

Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).

Signed-off-by: Eli Cohen <eli@mellanox.co.il>

[ Many things cleaned up and otherwise monkeyed with; hope I didn't
  introduce too many bugs.  - Roland ]

Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add fields to hardware data structures and add new constants required for IBoE
support.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix the limit on the size of max fast registration WRs that can be
posted to match hardware capabilities.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>