linux-toradex.git/include/linux/mlx5, branch v3.17-rc4

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2014-08-06T16:38:14+00:00

Pull networking updates from David Miller:
 "Highlights:

   1) Steady transitioning of the BPF instructure to a generic spot so
      all kernel subsystems can make use of it, from Alexei Starovoitov.

   2) SFC driver supports busy polling, from Alexandre Rames.

   3) Take advantage of hash table in UDP multicast delivery, from David
      Held.

   4) Lighten locking, in particular by getting rid of the LRU lists, in
      inet frag handling.  From Florian Westphal.

   5) Add support for various RFC6458 control messages in SCTP, from
      Geir Ola Vaagland.

   6) Allow to filter bridge forwarding database dumps by device, from
      Jamal Hadi Salim.

   7) virtio-net also now supports busy polling, from Jason Wang.

   8) Some low level optimization tweaks in pktgen from Jesper Dangaard
      Brouer.

   9) Add support for ipv6 address generation modes, so that userland
      can have some input into the process.  From Jiri Pirko.

  10) Consolidate common TCP connection request code in ipv4 and ipv6,
      from Octavian Purdila.

  11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.

  12) Generic resizable RCU hash table, with intial users in netlink and
      nftables.  From Thomas Graf.

  13) Maintain a name assignment type so that userspace can see where a
      network device name came from (enumerated by kernel, assigned
      explicitly by userspace, etc.) From Tom Gundersen.

  14) Automatic flow label generation on transmit in ipv6, from Tom
      Herbert.

  15) New packet timestamping facilities from Willem de Bruijn, meant to
      assist in measuring latencies going into/out-of the packet
      scheduler, latency from TCP data transmission to ACK, etc"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
  cxgb4 : Disable recursive mailbox commands when enabling vi
  net: reduce USB network driver config options.
  tg3: Modify tg3_tso_bug() to handle multiple TX rings
  amd-xgbe: Perform phy connect/disconnect at dev open/stop
  amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
  net: sun4i-emac: fix memory leak on bad packet
  sctp: fix possible seqlock seadlock in sctp_packet_transmit()
  Revert "net: phy: Set the driver when registering an MDIO bus device"
  cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
  team: Simplify return path of team_newlink
  bridge: Update outdated comment on promiscuous mode
  net-timestamp: ACK timestamp for bytestreams
  net-timestamp: TCP timestamping
  net-timestamp: SCHED timestamp on entering packet scheduler
  net-timestamp: add key to disambiguate concurrent datagrams
  net-timestamp: move timestamp flags out of sk_flags
  net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
  cxgb4i : Move stray CPL definitions to cxgb4 driver
  tcp: reduce spurious retransmits due to transient SACK reneging
  qlcnic: Initialize dcbnl_ops before register_netdev
  ...

mlx5: Adjust events to use unsigned long param instead of void *

2014-07-30T21:00:06+00:00

In the event flow, we currently pass only a port number in the
void *data argument.  Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.

In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.

Based on a patch by Eli Cohen 

Signed-off-by: Jack Morgenstein 
Signed-off-by: Eli Cohen 
Signed-off-by: David S. Miller

mlx5: minor fixes (mainly avoidance of hidden casts)

2014-07-30T21:00:06+00:00

There were many places where parameters which should be u8/u16 were
integer type.

Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).

Signed-off-by: Jack Morgenstein 
Signed-off-by: Eli Cohen 
Signed-off-by: David S. Miller

mlx5: Move pci device handling from mlx5_ib to mlx5_core

2014-07-30T21:00:06+00:00

In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.

This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
   is now an independent structure maintained by mlx5_core.
   mlx5_ib_dev now has a pointer to that struct.
   This requires changing a lot of places where the core_dev
   struct was accessed via mlx5_ib_dev (now, this needs to
   be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
   it is now mlx5_core which does pci_register_device (and not
   mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
   driver. This is very similar to the mechanism employed for
   the mlx4 (ConnectX) driver. Once the HCA is initialized
   (by mlx5_core), it invokes the interface drivers to do
   their initializations.
4. There is a new event handler which the core registers:
   mlx5_core_event(). This event handler invokes the
   event handlers registered by the interfaces.

Based on a patch by Eli Cohen 

Signed-off-by: Jack Morgenstein 
Signed-off-by: Eli Cohen 
Signed-off-by: David S. Miller

net: mlx5: Use ktime_get_ns()

2014-07-23T22:01:43+00:00

This code is beyond silly:

     struct timespec ts = ktime_get_ts();
     ktime_t ktime = timespec_to_ktime(ts);

Further down the code builds the delta of two ktime_t values and
converts the result to nanoseconds.

Use ktime_get_ns() and replace all the nonsense.

Signed-off-by: Thomas Gleixner 
Cc: Eli Cohen 
Signed-off-by: John Stultz

mlx5_core: Store MR attributes in mlx5_mr_core during creation and after UMR

2014-05-27T18:53:06+00:00

The patch stores iova, pd and size during mr creation and after UMRs
that modify them.  It removes the unused access flags field.

Signed-off-by: Haggai Eran 
Signed-off-by: Roland Dreier

IB/mlx5: Add block multicast loopback support

2014-04-11T01:43:32+00:00

Add support for the block multicast loopback QP creation flag along
the proper firmware API for that.

Signed-off-by: Eli Cohen 
Signed-off-by: Or Gerlitz 
Signed-off-by: Roland Dreier

IB/mlx5: Collect signature error completion

2014-03-07T19:40:04+00:00

This commit takes care of the generated signature error CQE generated
by the HW (if happened).  The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.

Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().

In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).

Signed-off-by: Sagi Grimberg 
Signed-off-by: Roland Dreier

IB/mlx5: Support IB_WR_REG_SIG_MR

2014-03-07T19:39:51+00:00

This patch implements IB_WR_REG_SIG_MR posted by the user.

Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:

1. post UMR WR to register the sig_mr in one of two possible ways:
    * In case the user registered a single MR for data so the UMR data segment
      consists of:
      - single klm (data MR) passed by the user
      - BSF with signature attributes requested by the user.
    * In case the user registered 2 MRs, one for data and one for protection,
      the UMR consists of:
      - strided block format which includes data and protection MRs and
        their repetitive block format.
      - BSF with signature attributes requested by the user.

2. post SET_PSV in order to set the memory domain initial
   signature parameters passed by the user.
   SET_PSV is not signaled and solicited CQE.

3. post SET_PSV in order to set the wire domain initial
   signature parameters passed by the user.
   SET_PSV is not signaled and solicited CQE.

* After this compound WR we place a small fence for next WR to come.

This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.

Signed-off-by: Sagi Grimberg 
Signed-off-by: Roland Dreier

IB/mlx5: Keep mlx5 MRs in a radix tree under device

2014-03-07T19:26:49+00:00

This will be useful when processing signature errors on a specific
key.  The mlx5 driver will lookup the matching mlx5 memory region
structure and mark it as dirty (contains signature errors).

Signed-off-by: Sagi Grimberg 
Signed-off-by: Roland Dreier