linux-toradex.git/include/linux/netdevice.h, branch v3.0.16

gro: Only reset frag0 when skb can be pulled

2011-08-05T04:58:31+00:00

commit 17dd759c67f21e34f2156abcf415e1f60605a188 upstream.

Currently skb_gro_header_slow unconditionally resets frag0 and
frag0_len.  However, when we can't pull on the skb this leaves
the GRO fields in an inconsistent state.

This patch fixes this by only resetting those fields after the
pskb_may_pull test.

Signed-off-by: Herbert Xu 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: remove NETIF_F_ALL_TX_OFFLOADS

2011-07-14T22:18:49+00:00

There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.

For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.

This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.

NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.

Signed-off-by: Michał Mirosław 
Signed-off-by: David S. Miller

net: Rework netdev_drivername() to avoid warning.

2011-06-06T23:41:33+00:00

This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:

net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername

Just return driver->name directly or "".

Reported-by: Connor Hansen 
Signed-off-by: David S. Miller

macvlan: remove one synchronize_rcu() call

2011-05-20T04:33:18+00:00

When one macvlan device is dismantled, we can avoid one
synchronize_rcu() call done after deletion from hash list, since caller
will perform a synchronize_net() call after its ndo_stop() call.

Add a new netdev->dismantle field to signal this dismantle intent.

Reduces RTNL hold time.

Signed-off-by: Eric Dumazet 
CC: Patrick McHardy 
CC: Ben Greear 
Signed-off-by: David S. Miller

netdevice.h: Align struct net_device members

2011-05-13T18:07:23+00:00

Save a bit of space.

Signed-off-by: Joe Perches 
Signed-off-by: David S. Miller

net: introduce netdev_change_features()

2011-05-12T22:40:56+00:00

It will be needed by bonding and other drivers changing vlan_features
after ndo_init callback.

As a bonus, this includes kernel-doc for netdev_update_features().

Signed-off-by: Michał Mirosław 
Signed-off-by: David S. Miller

net: group FCoE related feature flags

2011-05-12T21:54:16+00:00

Michał Mirosław's patch (http://patchwork.ozlabs.org/patch/94421/) fixes the
issue (http://patchwork.ozlabs.org/patch/94188/) about not populating FCoE related
flags correctly on vlan devices. However, only NETIF_F_FCOE_CRC is part of the
NETIF_F_ALL_TX_OFFLOADS right now, where weed NETIF_F_FCOE_MTU and NETIF_F_FSO
as well.

Therefore, add NETIF_F_ALL_FCOE to indicate feature flags used by FCoE TX offloads.
These include NETIF_F_FCOE_CRC, NETIF_F_FCOE_MTU, and NETIF_F_FSO and add them to
be part of NETIF_F_ALL_TX_OFFLOADS. This would eventually make sure all FCoE needed
flags are populated properly to vlan devices.

Signed-off-by: Yi Zou 
Signed-off-by: David S. Miller

net: Allow ethtool to set interface in loopback mode.

2011-05-08T22:59:12+00:00

This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.

Following set of commands illustrates one such example -
    a) ip -4 addr add 192.168.1.1/24 dev eth1
    b) ip -4 rule add from all iif eth1 lookup 250
    c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
    d) arp -Ds 192.168.1.100 eth1
    e) arp -Ds 192.168.1.200 eth1
    f) sysctl -w net.ipv4.ip_nonlocal_bind=1
    g) sysctl -w net.ipv4.conf.all.accept_local=1
    # Assuming that the machine has 8 cores
    h) taskset 000f netserver -L 192.168.1.200
    i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30

Signed-off-by: Mahesh Bandewar 
Acked-by: Ben Hutchings 
Signed-off-by: David S. Miller

ethtool: Call ethtool's get/set_settings callbacks with cleaned data

2011-04-29T21:01:30+00:00

This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).

This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.

All drivers visible to make allyesconfig under x86_64 have been
updated.

Signed-off-by: David Decotigny 
Signed-off-by: David S. Miller

net: allow user to change NETIF_F_HIGHDMA

2011-04-28T20:33:08+00:00

NETIF_F_HIGHDMA is like any other TX offloads, so allow user to toggle it.
This is needed later for bridge and bonding convertsion to hw_features.

Signed-off-by: Michał Mirosław 
Signed-off-by: David S. Miller