linux-toradex.git/include/linux/of_gpio.h, branch v5.16-rc3

gpiolib: constify passed device_node pointer

2021-08-05T19:21:58+00:00

Several gpiolib functions receive pointer to struct device_node which is
later passed to OF functions.  These OF functions accept already pointer
to const, so gpiolib can follow similar approach to indicate they are
not modifying the struct device_node.

Signed-off-by: Krzysztof Kozlowski 
Reviewed-by: Rob Herring 
Signed-off-by: Bartosz Golaszewski

gpio: Avoid kernel.h inclusion where it's possible

2020-02-10T11:58:36+00:00

Inclusion of kernel.h increases the mess with the header dependencies.
Avoid kernel.h inclusion where it's possible.

Besides that, clean up a bit other inclusions inside GPIO subsystem headers.
It includes:
 - removal pin control bits (forward declaration and header) from linux/gpio.h
 - removal of.h from asm-generic/gpio.h
 - use of explicit headers in gpio/consumer.h
 - add FIXME note with regard to gpio.h inclusion in of_gpio,h

Signed-off-by: Andy Shevchenko 
Link: https://lore.kernel.org/r/20200205134336.20197-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij

gpio: of: Make of_gpio_simple_xlate() private

2019-09-11T13:46:02+00:00

Since commit 9a95e8d25a140ba9 ("gpio: remove etraxfs driver"), there are
no more users of of_gpio_simple_xlate() outside gpiolib-of.c.
All GPIO drivers that need it now rely on of_gpiochip_add() setting it
up as the default translate function.

Signed-off-by: Geert Uytterhoeven 
Link: https://lore.kernel.org/r/20190906084539.21838-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij

gpio: add core support for pull-up/pull-down configuration

2019-02-13T08:10:14+00:00

This commit adds support for configuring the pull-up and pull-down
resistors available in some GPIO controllers. While configuring
pull-up/pull-down is already possible through the pinctrl subsystem,
some GPIO controllers, especially simple ones such as GPIO expanders
on I2C, don't have any pinmuxing capability and therefore do not use
the pinctrl subsystem.

This commit implements the GPIO_PULL_UP and GPIO_PULL_DOWN flags,
which can be used from the Device Tree, to enable a pull-up or
pull-down resistor on a given GPIO.

The flag is simply propagated all the way to the core GPIO subsystem,
where it is used to call the gpio_chip ->set_config callback with the
appropriate existing PIN_CONFIG_BIAS_* values.

Signed-off-by: Thomas Petazzoni 
Signed-off-by: Linus Walleij

Merge tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

2018-02-01T18:57:45+00:00

Pull DeviceTree updates from Rob Herring:

 - Convert to use memblock_virt_alloc in DT code which supports
   bootmem arches. With this we can remove the arch specific
   early_init_dt_alloc_memory_arch() functions.

 - Enable running the DT unittests on UML

 - Use SPDX license tags on DT files

 - Fix early FDT kconfig ifdef logic

 - Clean-up unittest Makefile

 - Fix function comment for of_irq_parse_raw

 - Add missing documentation for linux,initrd-{start,end} properties

 - Clean-up of binding examples using uppercase hex

 - Add trivial devices W83773G and Infineon TLV493D-A1B6

 - Add missing STM32 SoC bindings

 - Various small binding doc fixes

* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
  xtensa: remove arch specific early DT functions
  x86: remove arch specific early_init_dt_alloc_memory_arch
  nios2: remove arch specific early_init_dt_alloc_memory_arch
  mips: remove arch specific early_init_dt_alloc_memory_arch
  metag: remove arch specific early DT functions
  cris: remove arch specific early DT functions
  libfdt: remove unnecessary include directive from 
  of: unittest: refactor Makefile
  of/fdt: use memblock_virt_alloc for early alloc
  of: Use SPDX license tag for DT files
  of/fdt: Fix #ifdef dependency of early flattree declarations
  dt-bindings: h8300 clocksource: correct spelling of pulse
  dt-bindings: imx6q-pcie: Add required property for i.MX6SX
  mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
  dt-bindings: Use lower case hex in unit-addresses
  dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
  dt-bindings: Add Infineon TLV493D-A1B6
  dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
  dt-bindings: chosen: Document linux,initrd-{start,end}
  dt-bindings: arm: document supported STM32 SoC family
  ...

of: Use SPDX license tag for DT files

2018-01-08T14:22:45+00:00

Convert remaining DT files to use SPDX-License-Identifier tags.

Cc: Benjamin Herrenschmidt 
Cc: Guennadi Liakhovetski 
Cc: Paul Mackerras 
Cc: Pantelis Antoniou 
Reviewed-by: Frank Rowand 
Reviewed-by: Philippe Ombredanne 
Signed-off-by: Rob Herring

gpio: gpiolib: Generalise state persistence beyond sleep

2017-12-02T21:42:34+00:00

General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.

The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific.  I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.

The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.

Signed-off-by: Andrew Jeffery 
Reviewed-by: Charles Keepax 
Acked-by: Rob Herring 
Signed-off-by: Linus Walleij

gpio: Fix loose spelling

2017-10-20T07:37:32+00:00

Literally.

I expect "lose" was meant here, rather than "loose", though you could feasibly
use a somewhat uncommon definition of "loose" to mean what would be meant by
"lose": "Loose the hounds" for instance, as in "Release the hounds".
Substituting in "value" for "hounds" gives "release the value", and makes some
sense, but futher substituting back to loose gives "loose the value" which
overall just seems a bit anachronistic.

Instead, use modern, pragmatic English and save a character.

Cc: Russell Currey 
Signed-off-by: Andrew Jeffery 
Signed-off-by: Linus Walleij

gpio: Add new flags to control sleep status of GPIOs

2017-05-29T09:07:55+00:00

Add new flags to allow users to specify that they are not concerned with
the status of GPIOs whilst in a sleep/low power state.

Signed-off-by: Charles Keepax 
Acked-by: Rob Herring 
Signed-off-by: Linus Walleij

gpio: core: Decouple open drain/source flag with active low/high

2017-04-07T10:23:29+00:00

Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.

The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.

In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.

In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.

With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.

Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.

Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.

Signed-off-by: Laxman Dewangan 
Signed-off-by: Linus Walleij