linux-toradex.git/include/linux/pm.h, branch v4.6-rc3

PM / sleep: Go direct_complete if driver has no callbacks

2016-01-08T00:12:06+00:00

If a suitable prepare callback cannot be found for a given device and
its driver has no PM callbacks at all, assume that it can go direct to
complete when the system goes to sleep.

The reason for this is that there's lots of devices in a system that do
no PM at all and there's no reason for them to prevent their ancestors
to do direct_complete if they can support it.

Signed-off-by: Tomeu Vizoso 
Reviewed-by: Ulf Hansson 
Signed-off-by: Rafael J. Wysocki

PM / PCI / ACPI: Kick devices that might have been reset by firmware

2015-10-14T00:17:34+00:00

There is a concern that if the platform firmware was involved in
the system resume that's being completed,  some devices might have
been reset by it and if those devices had the power.direct_complete
flag set during the preceding suspend transition, they may stay
in a reset-power-on state indefinitely (until they are runtime-resumed
and then suspended again).  That may not be a big deal from the
individual device's perspective, but if the system is an SoC, it may
be prevented from entering deep SoC-wide low-power states on idle
because of that.

The devices that are most likely to be affected by this issue are
PCI devices and ACPI-enumerated devices using the general ACPI PM
domain, so to prevent it from happening for those devices, force a
runtime resume for them if they have their power.direct_complete
flags set and the platform firmware was involved in the resume
transition currently in progress.

Signed-off-by: Rafael J. Wysocki

Merge branch 'pm-wakeirq'

2015-06-18T23:18:14+00:00

* pm-wakeirq:
  PM / wakeirq: Fix typo in prototype for dev_pm_set_dedicated_wake_irq
  PM / Wakeirq: Add automated device wake IRQ handling

PM / Wakeirq: Add automated device wake IRQ handling

2015-05-19T23:56:31+00:00

Turns out we can automate the handling for the device_may_wakeup()
quite a bit by using the kernel wakeup source list as suggested
by Rafael J. Wysocki .

And as some hardware has separate dedicated wake-up interrupt
in addition to the IO interrupt, we can automate the handling by
adding a generic threaded interrupt handler that just calls the
device PM runtime to wake up the device.

This allows dropping code from device drivers as we currently
are doing it in multiple ways, and often wrong.

For most drivers, we should be able to drop the following
boilerplate code from runtime_suspend and runtime_resume
functions:

	...
	device_init_wakeup(dev, true);
	...
	if (device_may_wakeup(dev))
		enable_irq_wake(irq);
	...
	if (device_may_wakeup(dev))
		disable_irq_wake(irq);
	...
	device_init_wakeup(dev, false);
	...

We can replace it with just the following init and exit
time code:

	...
	device_init_wakeup(dev, true);
	dev_pm_set_wake_irq(dev, irq);
	...
	dev_pm_clear_wake_irq(dev);
	device_init_wakeup(dev, false);
	...

And for hardware with dedicated wake-up interrupts:

	...
	device_init_wakeup(dev, true);
	dev_pm_set_dedicated_wake_irq(dev, irq);
	...
	dev_pm_clear_wake_irq(dev);
	device_init_wakeup(dev, false);
	...

Signed-off-by: Tony Lindgren 
Signed-off-by: Rafael J. Wysocki

PM / sleep: Add macro to define common noirq system PM callbacks

2015-05-12T21:51:36+00:00

The same approach is used as for the existing SET_SYSTEM_SLEEP_PM_OPS,
but for noirq callbacks.

New SET_NOIRQ_SYSTEM_SLEEP_PM_OPS, defined for CONFIG_PM_SLEEP, will
point ->suspend_noirq, ->freeze_noirq and ->poweroff_noirq to the same
function. Vice versa happens for ->resume_noirq, ->thaw_noirq and
->restore_noirq.

Signed-off-by: Grygorii Strashko 
Acked-by: Santosh Shilimkar 
Reviewed-by: Ulf Hansson 
Acked-by: Pavel Machek 
Reviewed-by: Kevin Hilman 
Signed-off-by: Rafael J. Wysocki

driver core / PM: Add PM domain callbacks for device setup/cleanup

2015-03-22T21:14:12+00:00

If PM domains are in use, it may be necessary to prepare the code
handling a PM domain for driver probing.  For example, in some
cases device drivers rely on the ability to power on the devices
with the help of the IO runtime PM framework and the PM domain
code needs to be ready for that.  Also, if that code has not been
fully initialized yet, the driver probing should be deferred.

Moreover, after the probing is complete, it may be necessary to
put the PM domain in question into the state reflecting the current
needs of the devices in it, for example, so that power is not drawn
in vain.  The same should be done after removing a driver from
a device, as the PM domain state may need to be changed to reflect
the new situation.

For these reasons, introduce new PM domain callbacks, ->activate,
->sync and ->dismiss called, respectively, before probing for a
device driver, after the probing has completed successfully and
if the probing has failed or the driver has been removed.

Signed-off-by: Rafael J. Wysocki 
Acked-by: Ulf Hansson 
Reviewed-by: Kevin Hilman 
Acked-by: Greg Kroah-Hartman

PM: Convert dev_pm_put_subsys_data() into a void function

2015-02-03T21:59:25+00:00

Clients using the dev_pm_put_subsys_data() API isn't interested of a
return value. They care only of decreasing a reference to the device's
pm_subsys_data. So, let's convert the API to a void function, which
anyway seems like reasonable thing to do.

Signed-off-by: Ulf Hansson 
Acked-by: Geert Uytterhoeven 
Signed-off-by: Rafael J. Wysocki

PM: Remove the SET_PM_RUNTIME_PM_OPS() macro

2014-12-12T23:45:24+00:00

There're now no users left of the SET_PM_RUNTIME_PM_OPS() macro, since
all have converted to use the SET_RUNTIME_PM_OPS() macro instead, so
let's remove it.

Signed-off-by: Ulf Hansson 
Signed-off-by: Rafael J. Wysocki

Merge branch 'pm-runtime'

2014-12-08T19:00:44+00:00

* pm-runtime: (25 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  PM / Kconfig: Do not select PM directly from Kconfig files
  PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
  ...

PM: Merge the SET*_RUNTIME_PM_OPS() macros

2014-12-03T23:51:30+00:00

The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.

However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.

For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.

Reviewed-by: Ulf Hansson 
Acked-by: Kevin Hilman 
Signed-off-by: Rafael J. Wysocki