Pull tty / serial driver updates from Greg KH:
 "Here is the big set of tty and serial driver changes for 6.0-rc1.

  It was delayed from last week as I wanted to make sure the last commit
  here got some good testing in linux-next and elsewhere as it seemed to
  show up only late in testing for some reason.

  Nothing major here, just lots of cleanups from Jiri and Ilpo to make
  the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).

  Also included in here is the obligatory n_gsm updates from Daniel
  Starke and lots of tiny driver updates and minor fixes and tweaks for
  other smaller serial drivers.

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
  tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
  tty: amiserial: Fix comment typo
  tty: serial: document uart_get_console()
  tty: serial: serial_core, reformat kernel-doc for functions
  Documentation: serial: link uart_ops properly
  Documentation: serial: move GPIO kernel-doc to the functions
  Documentation: serial: dedup kernel-doc for uart functions
  Documentation: serial: move uart_ops documentation to the struct
  dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
  serial: mvebu-uart: uart2 error bits clearing
  tty: serial: fsl_lpuart: correct the count of break characters
  serial: stm32: make info structs static to avoid sparse warnings
  serial: fsl_lpuart: zero out parity bit in CS7 mode
  tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
  serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
  tty: vt: initialize unicode screen buffer
  serial: remove VR41XX serial driver
  serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
  serial: 8250_dwlib: remove redundant sanity check for RS485 flags
  dt_bindings: rs485: Correct delay values
  ...

While it's a lot of text, it always helps to keep it up to date when
it's by the source. (And not in a separate file.)

The documentation tooling also makes sure that all members of the
structure are documented. (If not, it complains loudly.)

Finally, there needs to be no comments inlined in the structure, so they
are dropped as they are superfluous now.

The compilation time of this header (tested with serial_core.c) didn't
change in my testing at all.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.

Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):

[    0.068987] univ8250_console_setup ttyS0 nodev
[    0.499670] printk: console [ttyS0] enabled
[    0.717955] printk: console [ttyS0] printing thread started
[    1.960163] serial8250_register_ports assigned dev for ttyS0
[    1.976830] printk: console [ttyS0] disabled
[    1.976888] printk: console [ttyS0] printing thread stopped
[    1.977073] univ8250_console_exit ttyS0 usage:0
[    1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[    1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[    1.977812] univ8250_console_setup ttyS0 usage:2
[    1.978167] printk: console [ttyS0] printing thread started
[    1.978203] printk: console [ttyS0] enabled

To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.

This problem became apparent only recently because 82586a721595 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).

Fixes: bedb404e91bb ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/b4f428e9-491f-daf2-2232-819928dc276e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 31f6bd7fad3b ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.

Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the tty/serial fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Preparing to move serial_rs485 struct sanitization into serial core,
each driver has to provide what fields/flags it supports. This
information is pointed into by rs485_supported.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.

In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In suspend sequence there is a need to perform stop_rx during suspend
sequence to prevent any asynchronous data over rx line. However this
can cause problem to drivers which dont do re-start_rx during set_termios.

Add new callback start_rx and perform stop_rx only when implementation of
start_rx is present. Also add call to start_rx in resume sequence so that
drivers who come across this problem can make use of this framework.

Fixes: c9d2325cdb92 ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1654627965-1461-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>